Slew Drive catalogue 2024

About us TECMA DRIVE is a brand that has positioned itself in the industrial and solar market with the versaiity and quality that a product needs to satisfy the demands of the wide and overparticular sector. Behind TECMA DRIVE there is a long trajectory in the sector with more than 15 years of experience, which allows us to commercialise and guarantee a product that satisfies the needs of the market. To cover the wide demands in different sectors, TECMA DRIVE can provide technical support and calculation solutions. In addition, ail factories involved in the manufacture of our products have current...

Index • Slew Drive Applications A Overview of applications and sectors where Slew Drives are used Definition and operation of Slew Drives Recommended types of lubricans and maintenance frequency • Slew Drive Structure 12 Main components and design of Slew Drives • Slew Drive Models 14 Description and characteristics of the different available models Technical data for the TD-E model Technical data for the TD-2-E model Technical data for the TD-W model Technical data for the TD-W-2 model Description of available accessories Slew Drive Catalogue

Slew Drive ApplicationsCharacteristics of Slew DrivesRefer to the table below for a guide on the safety factor to apply to your application.To determine the required rated slew drive capacity, multiply the applicable safety factor by the applied loads on the slew drive and compare the resulting loads to the load capacity curves. The application load case must be below the limit curve. Low Applications Safety Factor

Slew Drive Applications

Basic InformationSlew Drive mounting Slew Drives must be mounted according to the following instructions: The end shaft must be at the bottom. Otherwise the grease will not work properly. Slew Drives may be installed vertically and horizontally, but only when the angle between the slew and the horizontal plance angle is greater than 3 degrees. Horizontal installation with the base upwards Recommended installation if the Slew Drive is installed horizontally There is a risk of water ingress when used outdoors

Basic InformationStorage During storage, please, keep the slew drive packaging box in the specified direction and store it in a closed room to avoid moisture. While it's inside its packaging, the surface is corrosion-resistant and rust-proof, which can last for about 5 months. If it needs to be stored for a longer time, please take special protection measures. • After unpacking, two lifting rings can be fitted to the threaded holes in the slew drive outer ring for lifting and handling. The structure on which it will be mounted must meet certain requirements, considering a maximum flatness deviation....

Basic Information • It is recommended to apply thread-locking adhesive to the threaded connection. •The installation bolts should be tightened in a diagonal and crosswise pattern. Begin by tightening ail bolts diagonally to 30% of the specified torque, then repeat the process to 50%, and finally to 100% of the specified torque. • After the bolt is tightened, mark the bolts to facilitate future inspections for looseness. Tightening torque table for mounting bolts (for reference only): • During the installation process of the slew drive, the surface paint may become damaged. After the final assembly...

LubricationHow to grease your Slew Drive • Slew drives are supplied with the slew ring raceway, screw worm, and bearings pre-lubricated. They shall be greased again prior to initial operation and relubricated as needed based on working conditions. • In the event of abnormal noise or grease leakage during the use, stop the machine immediately to check and add grease. • Insufficient lubrication will shorten the service life of the slew drive, and may even cause the failure of the slew drive. • The recommended maintenance period, grease guantity, and grease type for the slew drive are as follows:...

Lubrication Lubrication cycle table of slew drives:

Slew Drive Structure Exploded view of a Slew Drive

Slew Drive StructureStructural drawing of the Slew Drives Slew Drive elements 1 - Outer ring: External ring from the Slew Drive that can rotate freely on the horizontal axis. 2- Inner ring: Internal ring from the Slew Drive that can rotate freely on the horizontal axis. 3 - Seals: Protects the Slew Drive from dust, water or any dust that can enter to the raceway. 4 - Balls and spacers: The balls allow the rings to rotate freely on the horizontal axis, while preventing any movement on the vertical axis. Meanwhile, the spacers are placed between the balls to prevent friction between them, thus...

Slew Drive ModelsWhich of our Slew Drives fits you the most? The perfect solution for rotation and positioning in machinery, combining a worm gear with a slew ring. This Slew Drive version features a double row of balls, allowing it to support higher loads. The housing of these Slew Drives is reinforced to withstand more demanding applications. These Slew Drives feature a double worm gear, allowing them to achieve higher dynamic torque at the expense of rotational speed.

Performance Parameters SLEW DRIVE TD-EX Slew Drive Catalogue

TD-EDimensions SLEW DRIVE TD-EX

Performance Parameters SLEW DRIVE TD-2-E Slew Drive Catalogue

TD-2-E Dimensions SLEW DRIVE TD-2-E

TD-W Performance Parameters SLEW DRIVE TD-W Slew Drive Catal

TD-WDimensions SLEW DRIVE TD-W

TD-W-2 Performance Parameters SLEW DRIVE TD-W-2 Slew Drive Catalogue

TD-W-2 Dimensions SLEW DRIVE TD-W-2

You can visit us on the following sites to recieve the latest news 08791 Sant Lloreng d'Hortons (Barcelona) Spain