Free Wheels UF

Free Wheels UF

Free Wheels UF

Product catalog summary
Specifications:
The UF Series freewheels are not self-centering, requiring one or two bearings for proper alignment of the outer and inner races. Torque is transmitted from the shaft to the inner race via a key and from the outer race to the housing using front pullers. Shaft tolerance should be h6 or j6, and seating tolerance should be H7 or G7, or K6 if front pullers are not used. Lubrication is necessary before use, with oil lubrication required for high idle rotations.
Technical Data:
The document provides a detailed table of specifications for various UF models, including dimensions, weight, maximum rotational speeds for inner and outer races, and resistance torque. For example, the UF 8 model has a shaft diameter of 8 mm, a maximum inner race speed of 5000 min-1, and a resistance torque of 0.09 Nm.
Notes:
TMAX is twice the resistance torque (TN). The keyway follows DIN 6885 standards. The document includes a mounting example and notes that the inner race can be faster than the outer race and vice versa.
See more

Catalog excerpts

Free Wheels UF-1

Modell  |  Type UF Die Freiläufe der Serie UF sind nicht selbstzentriert. Deshalb ist es erforderlich, ein oder zwei Lager neben dem Freilauf zu platzieren, sodass der Außenring zentriert zum Innenring rotieren kann. The UF Series freewheels are not self-centring. It is therefore necessary to place one or two bearings next to the freewheel so that the outer race can rotate centrally to the inner race. Die Drehmomente werden von der Welle auf den Innenring mittels Passfeder und vom Außenring auf das Gehäuse mittels Frontmitnehmer übertragen. The torque forces are transmitted from the shaft to the inner race by means of a key and from the outer race to the seating by means of front pullers. Die Toleranz der Welle muss entweder h6 oder j6 sein; die Toleranz für das Gehäuse muss entweder H7 oder G7 sein. Wenn die Frontmitnehmer nicht benutzt werden, sollte die Gehäusetoleranz K6 sein. Shaft tolerance must be either h6 or j6; the tolerances for the seating must be either H7 or G7. When front pullers are not used, the seating tolerance should be K6. Vor Inbetriebnahme muss der Freilauf mit Schmiermitteln gemäß den Anweisungen auf Seite 45 geschmiert werden. Ölschmierung ist erforderlich, wenn eine hohe Anzahl an Umdrehungen im Leerlauf erreicht wird. Before being put onto service, the freewheels must be lubricated with suitable lubricant following the instructions given on page 45. Oil lubrication is essential when a high number of rotations in neutral is reached. Ausgabe 2011   |   Druckfehler, Maß- und Konstruktionsänderungen vorbehalten.

 Open the catalog to page 1
Free Wheels UF-2

Montagebeispiel Mounting example Modell  |  Type UF Modell Type Masse Weight nmax  1] Drehzahl Innenring Inner race nmax  2] Drehzahl Außenring Outer race Anmerkung TMAX = 2 x TN Passfedernut DIN 6885 Seite 1 1] Innenring ist schneller als Außenring 2] Außenring ist schneller als Innenring Druckfehler, Maß- und Konstruktionsänderungen vorbehalten.   |   Ausgabe 2011 Leerlaufdrehmoment Resistance torque Notes TMAX = 2 x TN Keyway DIN 6885 page 1 1] Inner race is faster than outer race 2] Outer race is faster than inner race

 Open the catalog to page 2
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.