Servo system/ Current-output type S21S series_S21180D

Product catalog summary

Specifications:
The document outlines the specifications for a current sensor, specifically the S21S180D15JN model. Key specifications include a primary nominal current of 180A, measuring resistance ranging from 0 to 68Ω at Vcc=±12V and 0 to 100Ω at Vcc=±15V, and a rated output current of 45mA with a turn ratio of 1:4000. The output current accuracy is ±1%, and the offset current is ≤ ±0.2mA. The maximum current is ±540A, and the output linearity is ≤ ±0.3%. The power supply voltage ranges from ±12V±5% to ±15V±5%, with a consumption current of ≤ ±16mA. The response time is ≤ 1μs at di/dt=100A/μs, and the thermal drift of gain is ≤ ±0.02%/℃. The insulation voltage is AC2500V for 1 minute, and the insulation resistance is ≥500MΩ at DC500V. The operating temperature range is -30℃ to +80℃, and the storage temperature range is -40℃ to +85℃.

Procedures and Recommendations:
The document emphasizes the importance of using the most up-to-date information and specifies that the product is intended for general electronics applications. It is not designed for use in critical applications such as medical devices or nuclear power control, where failure could result in severe consequences. Users are advised to ensure thorough safety and reliability checks when using the product in special environments, such as those with corrosive gases or strong electromagnetic radiation.

Important Notices:
The document includes several important notices, such as the potential for changes without prior notice, the need for users to verify safety in their designs, and the disclaimer of responsibility for any violations of intellectual property rights. It also highlights that the product is not designed to resist radiation and that reproduction of the document without permission is prohibited.

Dimensions and Weight:
The dimensions are provided in millimeters, with a typical weight of 60g. The terminal numbers and their corresponding functions are listed, including +Vcc, -Vcc, OUT, and N.C. Tolerances are specified as ±0.5mm unless otherwise noted.

Catalog excerpts

Servo system/ Current-output type S21S series_S21180D-1

電流センサ関連　CURRENT SENSORS 磁気平衡式電流出力型 Servo system / Current-output type 項　目 Spec 定格電流 Primary norminal current 測定抵抗 Measuring Resistance (at 80˚C) 　　　　定格出力電流 Rated output Current 出力電流精度 Output Current Accuracy 最大電流 Maximum Current 出力直線性 Output Linearity 電源電圧 Power supply voltage ±12V±5%〜±15V±5% (Ratad output current is restricted by Vcc) 消費電流 Consumption Current di/dt 応答速度 (@90% of If) Response Time 出力電流温度係数 Thermal drift of gain オフセト電流温度係数ッ Thermal drift of offset ヒステシス誤差リ Hysteresis error 絶縁耐圧 lnsulation voltage AC2500V、1分間(感応電流 0.5mA)、貫通部内側⇔端子一括間 AC2500V for 1 minute (Sensing current 0.5mA) inside of through hole ⇔ terminal 絶縁抵抗 lnsulation resistance ≧500MΩ (at DC500V) 貫通部内側⇔端子一括間 inside of through hole ⇔ terminal 動作温度範囲 Ambient Operating temperature 保存温度範囲 Ambient storage temperature 2 次側コイル抵抗値 Secondary coil resistance ※1 オフセト電流はコアヒステシス除去後の値とッリする。　Offset current value is after removal of core hysteresis. ※ UL承認条件につきしては、ま別紙を参照願います。　*Please refer to the another sheet about conditions of UL Recognition. Unless otherwise specified, tolerances shall be ±0.5mm Unit is [mm]

Open the catalog to page 1

Servo system/ Current-output type S21S series_S21180D-2

電流センサ関連 CURRENT SENSORS ご注意 Important Notice 1. 本書の記載内容は、改良などにより予告なく変更することがあります。ご使用の際には、最新の情報であることをご確認下さい。 2. 本製品は一般的な電子機器家電製品、事務機器、情報機器、通信端末機器、計測機器、産業機器などへの使用を意図しております。極めて高度な品質及び信頼性が要求され、その製品の故障や誤動作が人命・身体に危害を及ぼす機器、装置医療機器、輸送機器、交通信号制御機器、火災・防犯装置、航空宇宙機器、原子力制御、燃料制御、車載機器、各種安全装置などの特定用途に使用されることを目的として設計及び製造されたものではございません。本資料に個別に記載されている場合を除き、本特定用途に使用された場合には、お客様または第三者の損害等について当社はいかなる責任も負いかねます。 3. 当社は品質、信頼性の向上に努めておりますが、電流センサはある程度の確率で機能不具合、故障の発生は避けられません。故障の結果として、人身事故、火災事故、社会的損傷などを発生させないよう、使用者の責任において、装置やシステム上での十分な安全設計と確認を行って下さい。 4. 本書に記載されている動作例および回路例は、使用上の参考として示したもので、これらに起因する当社もしくは第三者の工業所有権、...

Open the catalog to page 2