Magnetic Proportion System/ Through Type and Busbar type L32P S05(B)FS series_L32PS05
2Pages

{{requestButtons}}

Catalog excerpts

Magnetic Proportion System/ Through Type and Busbar type L32P S05(B)FS series_L32PS05 - 1

電流センサ関連 CURRENT SENSORS 磁気比例式 貫通型 and バスバー型 Magnetic Proportion System / Through Type and Busbar Type 項 目 Spec 定格電流 Primary norminal current 飽和電流 Saturation current タ プ イ Type Through hole type : L32PxxxS05FS Bus bar type : L32PxxxS05BFS Through hole type +2.495V±0.020V※1 (at Rref ≥ 1MΩ. Ouput impedance : typ 200Ω) 定格出力電圧 Rated output voltage 出力直線性 Output linearity (0A If) 電源電圧 Power supply voltage 消費電流 Consumption current リ レンス電圧 ファ Reference Voltage di dt 応答速度 Response time リ レンス電圧温度係数 ファ Reference Temperature Characteristic 出力電圧温度特性 Thermal drift of gain オフセ ト電圧温度特性 (at If=0A) ッ Thermal drift of offset ヒステ シス誤差 (at 0A → If → 0A) リ Hysteresis error 絶縁耐圧 Insulation voltage AC2500V、1 分間感応電流 0.5mA1 次 ⇔ 2 次間 AC2500V for 1 minute(Sensing current 0.5mA) Primary ⇔ Secondary 絶縁抵抗 Insulation resistance 動作温度範囲 Ambient Operating temperature 保存温度範囲 Ambient storage temperature ※1 Vref端子に外部基準電圧(1.5V-2.8V / 5mA )を印加する とによ オフセ ト電圧Vofを調整する と こ り、 ッ こ が可能です。 Vref端子を使用 しない場合、 端子は未接続に して下さ  ※2 オフセ ト電圧はコアヒス い。 ッ テ シス除去後の値と リ する。  ※ UL承認条件につき しては、 ま 別紙を参照願います。  ※ 耐硫化対策内容(使用抵抗 内部電極金メ キ)  ※ フ ライ コアを使用 ッ ェ ト *1 It is possible to change Vof with an external reference voltage (between 1.5V - 2.8V providing its ability to sink or source approximately 5 mA.). If the external reference voltag is not used, the Vref pin should be left unconnected. *2 Offset voltage value is after removal of core hysteresis. *Please refer to the another sheet about conditions of UL Recognition. *AntiSulfurated (Used resistors : Gold internal Electrodes) *Ferrite core is used. 外形図 DIMENSIONS (mm) 端子番号 Terminal number ① Vcc (+5V) ② GND ③ Vout ④ Vref (IN/OUT) ⑤⑥ NC 質量 Weight 22g 端子番号 Terminal number ① Vcc (+5V) ② GND ③ Vout ④ Vref (IN/OUT) ⑤⑥ NC ⑦ Primary input current (+) ⑧ Primary input current (–) 質量 Weight 30g 注 Note 1. 指示なき寸法公差は±0.5mm Unless otherwise specified, tolerances shall be ±0.5mm 2. 外形寸法の単位はmmとする。 Unit is [mm] 注 Note 1. 指示なき寸法公差は±0.5mm Unless otherwise specified, tolerances shall be ±0.5mm 2. 外形寸法の単位はmmとする。 Unit is [mm]

Open the catalog to page 1
Magnetic Proportion System/ Through Type and Busbar type L32P S05(B)FS series_L32PS05 - 2

電流センサ関連 CURRENT SENSORS ご注意 Important Notice 1. 本書の記載内容は、改良などにより予告なく変更することがありま す。 ご使用の際には、最新の情報であることをご確認下さい。 2. 本製品は一般的な電子機器家電製品、事務機器、情報機器、通信 端末機器、計測機器、産業機器などへの使用を意図しております。 極めて高度な品質及び信頼性が要求され、その製品の故障や誤動 作が人命・身体に危害を及ぼす機器、装置医療機器、輸送機器、 交通信号制御機器、火災・防犯装置、航空宇宙機器、原子力制御、 燃料制御、車載機器、各種安全装置などの特定用途に使用される ことを目的として設計及び製造されたものではございません。 本資料に個別に記載されている場合を除き、本特定用途に使用され た場合には、お客様または第三者の損害等について当社はいかな る責任も負いかねます。 3. 当社は品質、信頼性の向上に努めておりますが、電流センサはある 程度の確率で機能不具合、故障の発生は避けられません。故障の 結果として、人身事故、火災事故、社会的損傷などを発生させないよ う、使用者の責任において、装置やシステム上での十分な安全設計 と確認を行って下さい。 4. 本書に記載されている動作例および回路例は、使用上の参考として...

Open the catalog to page 2

All Tamura Corporation catalogs and technical brochures

  1. S25PxxxD15*

    3 Pages

  2. S26P200D15Y

    3 Pages

  3. S29S1T0D24Z*

    4 Pages

  4. Current Sensors

    111 Pages

  5. L07PxxxS05

    2 Pages

  6. L07PxxxD15S

    2 Pages

  7. L07PxxxD15

    2 Pages

  8. F03PxxxS05

    8 Pages

  9. F01PxxxS05

    7 Pages