2CG010BBC11N Datasheet Gate Driver Module 2CG010BBC11N■ Overview Gate driver 2CG010BBC11N is a dual channel gate driver designed for IGBT and SiC MOSFET. The high breakdown voltage and low parasitic capacitance make it suitable for gate drives such as SiC MOSFET and IGBT. ■ Features •Ideal for drive of IGBT and SiC MOSFET •Gate voltage : +15V/-10V •ALL-IN-ONE (Built-in isolated DC / DC converter and gate drive circuit) •Low parasitic capacitance (about 12pF) ; highly resistant to common-mode noise. •Fast response : about 100nsec(typ) •The isolation for primary-secondary signal used fast response isolator. •Input-to-Output dielectric withstand voltage : AC5000V •Output CH1-to-Ouput CH2 dielectric withstand voltage : AC4000V •Input-to-Output insulation distance : 14mm (clearance), 16mm(creepage) (As for Gate driver module PCB) •Output CHl-to-Output CH2 insulation distance : 7mm (clearance), 12mm(creepage) •DC/DC converter input voltage :13~28V •Signal input voltage : 3.3V,5V •Overload protection (DC/DC converter) •Overheat protection (DC/DC converter) •Half bridge mode (Gate drive circuit) •Desaturation protection (Gate drive circuit) •Soft turn-off function (Gate drive circuit) •Fault signal output function (Gate drive circuit) •Miller function (Gate drive circuit) •Under-voltage lockout(UVLO) (Gate drive circuit) •Insulating moistureproof coating •Safety standards :UL508(file no.E243511) (DC/DC converter only) •Reinforced isolation according to IEC 60664-1 (IEC61800-5-1, IEC62477-1, IEC62109-1, etc.) ■ Application Industrial inverter, power conditioner, etc ■■■ TAMURA CORPORATION

2CG010BBC11N Datasheet ■ Circuit Image Prod uct Power supply (VIN+) Alarm output (CH1 Gate) Alarm output (CH2 Gate) Signal input (CH1 Gate) Signal input (CH2 Gate) Ground (GND) Power module ■ Pin Connection Input Output TAMURA CORPORATION

2CG010BBC11N Datasheet ■ Internal Block Diagram ■ I/O Condition Table No. O : Vox+ UVLO > UVLO, X : Don't care, SD :Shut down

<7TXWM2J3A ■ Absolute Maximum Ratings ■ Permissible frequency curve Total gate charge (Qg) vs permissible frequency curve TAMURA CORPORATION

<7TXWM2J3A ■ Electrical Specification (Vin=24V, Vcc=5V.Ta=25^, Unless otherwise specified) TAMURA CORPORATION

Mf you want to use past the long period there is a concern that the solder non-wetting by terminal oxidation to occur. Therefore, please use from taking enough tests. : 255±3V Less than 3sec Temperature of preheating 110V~130V End temperature of preheating 110V±10V : 360V(MAX) Less than 3sec •Flow soldering condition •Soldering condition of hand work • Always mount fuse on the plus side of input for ensuring safety because the fuse is not built-in the product. Please select the fuse considering conditions such as steady current, inrush current, and ambient temperature. When using a fuse having...

2CG Series Outline Drawing ■Outline Dimensional Drawing Unit: mm Note: 1. The dimensional tolerance without directions is ± 0.5mm. TAMURA CORPORATION

Important Notice ■Important Notice ● This information and product are subject to change without prior notice for the purpose of improvements, etc. Ensure that you are in possession of the most up-to-date information when using this product. ● The operation examples and circuit examples shown in this document are for reference purposes only, and TAMURA Corporation disclaims all responsibility for any violations of industrial property rights, intellectual property rights and any other rights owned by TAMURA Corporation or third parties that these may entail. ● The circuit examples and part constants...