■ High water protection IP68 (1bar / 30min) polyamide cable gland. Protection class : IP68 1bar / 30min Operating temperature : -20°C ~ +100°C Compliant with EN50262 Ver. A ■ Wide selection, for M8 ~ M50, suitable for 02.5mm ~ 042 mm cable. ■ Super tough and superior heat resistant PA6GF (glass fiber filled PA6) material on cap and connector. ■ Safer halogen free, eco-friendly product. Thicker sealing insert evenly hold a cable by having a larger holding area. Remains durable even after repeated tightening / loosening. Lamellar insert type If over-tightened, it can cause the rubber bush or cable to deform, which can allow water to seep in. Part name ■ Lock nut is not included for M8 and M10 sizes. Please drill an appropriate thread hole into the enclosure for installation. ■ Appropriate tightening torque varies by each cable diameter. Tighten the cap until top of the sealing insert forms a small bead between the cap and the cable.

■ No optional sealing washer is required when installing on an even surface because of the built-in waterproof rib. ■ An optional sealing washer is required when installing on an uneven surface. (See website for more information on the optional sealing washer AGP series) Sealing washer Sealing washer ■ DXF/DWG/PDF drawings available on our website. ■ Lock nut is not included for M8 and M10 sizes. Please drill an appropriate thread hole into the enclosure for installation. Product no. / Details Product no. Black Thread size Cable range Mounting hole

Cable Gland Recommended Torque REFERENCE TABLE - AG series The table below details the reference tightening torque values recommended for tightening of the cable gland. Excessive tightening may damage, or cause deformation to the cable, or to the cable gland itself. It is recommended to both utilize the table as a reference when tightening, as well as performing actual field testing to ascertain if the product/s are suitable to be used under the required conditions. Precautions should be taken when tightening to prevent damage and deformation of the components. When tightening, the connector...

AGP SERIES SEALING WASHER for AG* AGSP ■ Sealing washer for AG series. ■ Made from oil resistant NBR material. ■ Use in the case of installation on a rough or uneven surfaces. ■ Selectable in 7 sizes (from M12 to M50) ■ Sealing washer is not necessary for installation on flat surfaces. Product no. D1 D2 M Suitable cable gland

series INTERCHANGEABLE HEAD TORQUE WRENCH ■ Torque wrench with interchangeable head. Suitable for the tightening of cable glands requiring a specific torque. Open end interchangeable head (spanner head) TWE series available separately. Spanner head is not included. Product no. Length Torque range (N • m) Increments (N • m) The torque wrench is not subject to RoHS regulations. Since it is an OEM product and not a JIS-compliant product, no calibration services or inspection reports, etc. are provided. When tightening, proceed first with a low value (half of the reference) of the recommended torque,...

Suitable TWE model RM • RMW series

Please read this manual carefully before use while following operation instructions. The manufacturer / retailer etc. will not be are not liable for any personal injuries, , damage to the product, or other property damage, etc. caused by improper use. * Do not use beyond the maximum torque value. This may cause damage and injury. * Do not use the torque wrench as a hammer or lever, or applying strong impact. * Do not modify or disassemble the torque wrench. These may cause strength or accuracy problems, which may lead to accidents and injuries. * Before use, check for damage, cracks, rust, or...

Handle center Torque scale 3⃣ How to use ① Push and hold the ring down to unlock. ・Turn the handle while the ring is in the unlock position. ③ Adjust to required torque. ・The ring will spring back to its original (lock) position. TAKACHI ELECTRONICS ENCLOSURE CO., LTD. TEL. +81-48-222-5409 https://www.takachi-enclosure.