Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: ZS050YMM-J40 5.0″TFT Display Module (1080*1080) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.
Open the catalog to page 1
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification CONTENT LIST
Open the catalog to page 2
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification Record of Revisions Revision Pre.0 Initial Released
Open the catalog to page 3
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 1.0 GENERAL DESCRIPTION 1.1 Introduction ZS050YMM-N40 is a color active matrix TFT-LCD Panel using LTPS TFT's (Thin Film Transistors) as an active switching devices. This model is composed of a TFT-LCD Panel, a driving circuit and a back light system. It is a transmissive type display operating in the normal black. This TFT-LCD has a 5.0 inch diagonally measured active area with FHD resolutions (1080 horizontal by 1080 vertical pixel array). Each pixel is divided into Red, Green, Blue dots which are arranged...
Open the catalog to page 4
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 1.3 General Specifications (H: horizontal length, V: vertical length) Parameter Pixel Pitch Active Area Pixel Arrangement Display Colors Color Gamut Display Mode Normally Black, Transmissive mode Dimensional Outline Viewing Direction (Human Eye) Note: 136.531x132.208x1.98 U/D/L/R free viewing direction 1. At the U/D/L/R direction, the viewing angle is same; 2. The TFT and CF LC Algin Direction;
Open the catalog to page 5
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 2.0 ABSOLUTE MAXIMUM RATINGS The absolute maximum ratings are list on table as follows. When used out of the absolute maximum ratings, the LSI may be permanently damaged. Using the LSI within the following electrical characteristics limit is strongly recommended for normal operation. If these electrical characteristic conditions are exceeded during normal operation, the LSI will malfunction and cause poor reliability. Spec Parameter Symbol Unit Min. Max. Typ. Logic Power Supply IOVCC -0.3 +3.6 V Voltage Analog...
Open the catalog to page 6
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 3.0 ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module DC Characteristics Parameter Power Supply Input Voltage Analog Positive Power Supply Analog Negative Power Supply Low Level Input Voltage High Level Input Voltage Power Consumption Unit Remark - Note: Frame rate=60HZ, Typ. Pattern White pattern, worst case pattern 1×1 checker 25℃. 3.2 Backlight Driving Conditions Parameter Notes: 1. Calculator Value for reference ILED×VLED×LED Quantity = PLED 2. The LED Life-time define as the estimated time to 50%30000hrs...
Open the catalog to page 7
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 3.3 Block Diagram
Open the catalog to page 8
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 4.0 INTERFACE CONNECTION 4.1 Connector Part Number Connector Name / Designation Manufacturer Connector Model Number Signal Connector Hirose DF40C-50DP-0.4V 4.2 Electrical Interface Connection Pin NO.
Open the catalog to page 9
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 5.0 SIGNAL TIMING SPECIFICATION Vertical Timing
Open the catalog to page 10
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification Horizontal Timing
Open the catalog to page 11
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 6.0 POWER ON/OFF SEQUENCE Power on/off Sequence
Open the catalog to page 12
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 7.0 OPTICAL SPECIFICATIONS 7.1 Overview The test of Optical specifications shall be measured in a dark room(ambient luminance≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Topcon SR-UL1R and Westar TRD-100A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°.The center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. 7.2...
Open the catalog to page 13
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 3. Surface luminance is the center point across the LCD surface 50cm from the surface with all pixels displaying white. This measurement shall be taken at the locations shown in FIG. 1. 4. Uniformity measurement shall be taken at the locations shown in FIG. 2, for a total of the measurements per display, measure surface luminance of these nine points across the LCD surface 50cm from the surface with all pixels displaying white. Uniformity Min Luminance of 9 points Max Luminance of 9 points 5. The color...
Open the catalog to page 14
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification Figure 3. Response Time Testing
Open the catalog to page 15
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 8.0 MECHANICAL CHARACTERISTICS 8.1 Dimension Requirements for LCD Part Mechanical outlines for the panel (H: horizontal length, V: Vertical length) Parameter Panel size Active area Number of pixels Pixel pitch Pixel arrangement Dimensional outline Display mode Figure 5. LCM Outline Dimension (unit: mm)
Open the catalog to page 16
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification Test Item Test Condition High Temp Operation High Temp/ High humidity Operation High Temp Storage High Temp/ High Humidity Storage Thermal Shock 60 ℃/ 90% RH for 100 hours 75 ℃ for 240 hours 65 ℃/ 90% RH for 100 hours -30 ℃ for 240 hours -30 ℃ for 45min and then 75 ℃ for 45 min, 5 cycles Contac
Open the catalog to page 17
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification
Open the catalog to page 18
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification
Open the catalog to page 19
BOE Optoelectronics Technology CO., LTD ZS050YMM-J40 Module Product Specification 12.0 HANDDLING & CAUTIONS 12.1 Mounting Method The panel of the LCM consists of two thin glasses with polarizer which easily get damaged. So extreme care should be taken when handling the LCM. Excessive stress or pressure on the glass of the LCM should be avoided. Care must be taken to insure that no torsional or compressive forces are applied to the LCM unit when it is mounted. If the customer's set presses the main parts of the LCM, the LCM may show the abnormal display. But this phenomenon does not...
Open the catalog to page 20All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
