Manufacturer Certificated Product Specification Model: TTX156BHT-02 15.6″TFT Display Module (1920*1080) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

PRODUCT GROUP SPEC. NUMBER SPEC. TITLE ISSUE DATE TTX156BHT-02 Final Product Specification REVISION HISTORY Initial Release

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification ISSUE DATE 2021.08.23 PAGE OF 32 3 REVISION HISTORY General Description Absolute Maximum ratings Electrical specifications. Optical specifications. Interface Connection Signal Timing Specification Input Signals, Display Colors & Gray Scale of Colors Power Sequence Connector description Mechanical Characteristics Reliability Test Handling & Cautions. Packing information Mechanical Outline Dimension EDID Table

PRODUCT GROUP SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification ISSUE DATE 2021.08.23 PAGE OF 32 4 1. GENERAL DESCRIPTION 1. Introduction TTX156BHT-02 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 15.6 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 6bit+FRC colors and colorgamut 45%. The TFT-LCD panel used for...

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER ISSUE DATE SPEC. TITLE TTX156BHT-02 Final Product Specification 3. Application  Notebook PC (Wide type) 4. General Specification The followings are general specification (listed in Table 1.)

PRODUCT GROUP ISSUE DATE TFT- LCD PRODUCT SPEC. NUMBER T-01-00 SPEC. TITLE TTX156BHT-02 Final Product Specification 2. ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> Power Supply Voltage Logic Supply Voltage Operating Temperature Storage Temperature Remarks Note 1 Note 2 Notes : 1. Permanent damage to the device may occur if maximum values are exceeded functional operation should be restricted...

PRODUCT GROUP SPEC. NUMBER TTX156BHT-02 Final Product Specification SPEC. TITLE ISSUE DATE ELECTRICAL SPECIFICATIONS 1. Electrical Specifications < Table 3. Electrical specifications > Power Supply Voltage Permissible Input Ripple Voltage Power Supply Current Power Supply Inrush Current Power Consumption Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25 °C. a) Typ : Mosaic pattern 8*8 b) Max : R/G/B patterns 2. Calculated value for reference (VLED × ILED) 3. Measure condition

PRODUCT GROUP SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification 2 . Backlight Unit < Table 4. LED Driving guideline specifications > Parameter ISSUE DATE Power supply voltage for LED Driver Power Supply Voltage for LED Driver Inrush Iled inrush PWM Control Frequency Duty Ratio Notes : 1. Power supply voltage12V for LED Driver Calculator Value for reference IF × VF ×40 / efficiency = PLED 2. The LED Life-time define as the estimated time to 50% degradation of initial luminous. 3. 1% duty cycle is achievable with a dimming frequency less than 1KHz. 4. Measure condition .

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification ISSUE DATE 2021.08.23 PAGE OF 32 9

PRODUCT GROUP ISSUE DATE SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification OPTICAL SPECIFICATION 1. Overview The test of Optical specifications shall be measured in a dark room (ambient luminance  1 lux and temperature = 252℃) with the equipment of Luminance meter system (Goniometer system and PR730) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock...

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification ISSUE DATE 2021.08.23 PAGE 11 OF 32 Notes : 1.Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1). 2.Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to...

PRODUCT GROUP SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification ISSUE DATE 2021.08.23 PAGE 12 OF 32 Optical measurements Figure 1. Measurement Set Up TFT-LCD module Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (5 points) Center Luminance of white is defined as luminance values of center 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 12

PRODUCT GROUP ISSUE DATE SPEC. NUMBER SPEC. TITLE TTX156BHT-02 Final Product Specification Figure 3. Uniformity Measurement Locations (13 points) The White luminance uniformity on LCD surface is then expressed as : ΔY5 = Minimum Luminance of five points / Maximum Luminance of five points (see FIGURE 2) , ΔY13 = Minimum Luminance of 13 points /Maximum Luminance of 13 points (see FIGURE 3). Figure 4. Response Time Testing Dsplay data The electro-optical response time measurements shall be made as shown in FIGURE 4 by switching the “data” input signal ON and OFF. The times needed for the luminance...