Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TTX150BHT-01 15.0″TFT Display Module (1920*1080) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD. RECORDS OF REVISION DATE
Open the catalog to page 2
TAILOR PIXELS TECHNOLOGY CO., LTD. 1. Application This specification applies to a color TFT-LCM Module, 2. Overview This TFT-LCM Module is a color active matrix TFT LCD using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This FOB has a 15 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this LCM can display 16.7Mcolors. The TFT-LCD panel used for this FOB is a low reflection and higher color type . All input...
Open the catalog to page 3
TAILOR PIXELS TECHNOLOGY CO., LTD. Outline dimensions Parameter Unit outline dimensions 4. Input Terminals 4-1 Driving interface of PWB The electronics interface connector is UJU IS050-L30B-C10 or Compatible. Mating housing/ Part Number：I-PEX 20454-030T or Compatible The connector interface pin assignments are listed in Table 6. Pin No. High Speed round Complement Signal Link Lane 1 True Signal Link Lane 1 High Speed round Complement Signal Link Lane 0 True Signal Link Lane 0 High Speed round True Signal Auxiliary Channel Complement Signal Auxiliary Channel High Speed round Panel self test...
Open the catalog to page 4
TAILOR PIXELS TECHNOLOGY CO., LTD. Hot plug detect output Backlight ground Backlight ground Backlight ground Backlight ground Backlight on/off System PWM Reset low active LED Power Supply 5V-21V；If not use，NC LED Power Supply 5V-21V；If not use，NC LED Power Supply 5V-21V；If not use，NC LED Power Supply 5V-21V；If not use，NC *1 P: POWER I: Input O: Output
Open the catalog to page 5
TAILOR PIXELS TECHNOLOGY CO., LTD. Fig.4-2-4 eDP 2lane 6bit input data mapping Electrical Characteristics 5-1 Absolute Maximum Ratings Ratings Parameter Symbol Condition Backlight supply voltage Input voltage(eDP) Input voltage(BL) Storage temperature Operation temperature [Note 5-3] (*) “Absolute Maximum Ratings” is regulations that do not exceed it even momentarily. (*) Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. [Note 5-1] eDP signals [Note 5-2]Backlight control signals (BL_ENABLE,BL_PWM_DIM) [Note 5-3] Humidity: 90%RH Max.at...
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD. 5-2 Electrical Specifications Ta=25+/-2°C Parameter Power Supply Voltage Permissible Input Ripple Voltage High Level Power Supply Current Power Supply Inrush Current BIST Control Level Power Consumption Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25 ° C. a) Typ : Mosaic pattern 8*8 b) Max : R/G/B patterns Figure 3. Power Measure Patterns 2. Calculated value for reference (VLED × ILED) Figure 4. Inrush Measure Condition 3. Measure condition (Figure...
Open the catalog to page 7
TAILOR PIXELS TECHNOLOGY CO., LTD. 5.3. DC Characteristics 5-3-1. TFT-LCD panel driving The specification of the eDP Rx interface timing parameter is shown in Table 8. 5-3-2. POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off seq uence shall be as shown in below
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. 6 . Backlight driving The backlight system is an edge-lighting type with white-LED. (It is usually required to measure under the following condition: Ta=25℃±2℃) Parameter Supply voltage Current dissipation
Open the catalog to page 9
TAILOR PIXELS TECHNOLOGY CO., LTD. Backligh t off PWM Control Level Brightness Control Duty Ratio Brightness Control frequency Notes : 1. Power supply voltage12V for LED Driver Calculator Value for reference I F × V F ×70 / efficiency = P LED 2. The LED Life-time define as the estimated time to 50% degradation of initial luminous. 3. 1% duty cycle is achievable with a dimming frequency less than 1KHz. LED structure Backlight LED 10 串 7 并 70 颗 Circuit 7. Timing characteristics of input signals 7-1.Timing Characteristics (TBD) The TFT-LCM Module is operated by the DE only. Item High Time...
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. 7-2. Input data signals and display position on the screen Display position of input data(V·H)
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD. 7-3 Input sigal,basic display colors and gray scale of each color Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of 24 bit data signals, the 16.7M color display can be achieved on the screen.
Open the catalog to page 12
TAILOR PIXELS TECHNOLOGY CO., LTD. 8. ID Manufacturer Name ID Product Code EDID Header EDID revision # Video input definition Video Signal Interface Display Gamma Feature support Feature Support Blue / White Low Bits Green x high bits Green y high bits Blue x high bits
Open the catalog to page 13
TAILOR PIXELS TECHNOLOGY CO., LTD. BLue y high bits White x high bits White y high bits Detailed timing/monitor descriptor #1
Open the catalog to page 14
TAILOR PIXELS TECHNOLOGY CO., LTD. Detailed timing/monitor descriptor #2
Open the catalog to page 15
TAILOR PIXELS TECHNOLOGY CO., LTD. Detailed timing/monitor descriptor #3
Open the catalog to page 16
TAILOR PIXELS TECHNOLOGY CO., LTD. Detailed timing/monitor descriptor #4 Extension flag Notes: 1.EDID custom information not required 9. OPTICAL SPECIFICATION 9.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance≤1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and PR730) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°， We refer to θØ=0(=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock...
Open the catalog to page 17All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
