Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TTX133BHN-01 13.3″TFT Display Module (1920*1080) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD. General Description Absolute Maximum ratings Electrical specifications. Interface Connection Signal Timing Specifications Power Sequence Optical specifications. Mechanical Outline Dimension Reliability Test Packing information
Open the catalog to page 2
TAILOR PIXELS TECHNOLOGY CO., LTD. 1.0 GENERAL DESCRIPTION 1.0.1 Introduction TTX133BHN-01is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 13.3 inch diagonally measured active area with Full-HD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7 M colors. 1.0.2 Features ⚫ 2 lane eDP interface with 2.7Gbps link rates ⚫ Thin and light weight ⚫ 16.7M color depth, color gamut...
Open the catalog to page 3
TAILOR PIXELS TECHNOLOGY CO., LTD. 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Environment Absolute Maximum Ratings> [Ta =25±2 ℃] Parameter Back-light LED Reverse Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity Back-light Power Supply Voltage Back-light LED Current Heat Release Requirement Remarks Ta = 25 ℃ Note 1&2 Remarks Note: 1. These range above is...
Open the catalog to page 4
TAILOR PIXELS TECHNOLOGY CO., LTD. 2. Calculated value for reference ILED × VLED÷0.85 = PLED 3.2 Back-light Unit < Table 4. LED Driving guideline specifications > Parameter Supply voltage Power supply Current for Back light Power supply for Back light Modulated light signal voltage Brightness Control Duty Ratio Brightness Control frequency Duty fPWM LED-BL ON/OFF High voltage LED-BL ON/OFF low voltage Notes : 1. Calculator Value for reference ILED × VLED = PLED 2. The LED Life-time define as the estimated time to 50% degradation of initial luminous under the condition of the ambient...
Open the catalog to page 5
TAILOR PIXELS TECHNOLOGY CO., LTD. 4. INTERFACE CONNECTION 4-1 Electrical Interface Connection CN1 (eDP signals, +3.3V DC power supply and B/L power supply) Pin No. High Speed round Complement Signal Link Lane 1 True Signal Link Lane 1 High Speed Ground Complement Signal Link Lane 0 True Signal Link Lane 0 High Speed Ground True Signal Auxiliary Channel Complement Signal Auxiliary Channel High Speed Ground LCD logic and driver ground LCD logic and driver ground Backlight ground Backlight ground Backlight ground Backlight ground Backlight on/off Backlight power Backlight power Backlight...
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD. 4.2 Data Input Format Display Position of Input Data (V-H) 5.0 SIGNAL TIMING SPECIFICATION 5.0.1 The model is operated by the DE only. Item High Time Frame Period Vertical Display Period One line Scanning Period Horizontal Display Period Note: The DCLK range at last line of V-blanking should be set in 0-H-active/2.
Open the catalog to page 7
TAILOR PIXELS TECHNOLOGY CO., LTD. 6.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below Notes: 1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Back Light must be
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. 7.0 Optical characteristics 7.0.1 Overview The test of view angle range shall be measured in a dark room (ambient luminance ≤1lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON CS2000/CA310) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0 . We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θ Ø=90 (= θ12 ) as the 12 o’clock direction (“upward”), θ Ø=180 (= θ9 ) as the 9 o’clock direction (“left”) and θ Ø=270(= θ6...
Open the catalog to page 9
2.Do not scale drawing,Unit:mm. 3. n Modification rev.number. 0.2 4.Genral Tolerance: ± ,( ) reference dimension.带*的尺寸为重点管控尺寸 5.Draft angle 1.5° C C 6.Operating Temperature:-10~+50° ,Storage Temperature:-20~+60° 7.possession materials are insulated (ex FPC ,LED) 8.同一片背光色度坐标x/y要求：最大值与最小值相差不超过0.02; 9.平面度≤0.6.mm，变形方向为 Customer Name: Symbol Item min. Lv Luminance 265 Uniformity Avg Main 75 screen TBD X Colour Coordinate TBD Y 25.2 Forward Voltage Vf 视角要求: Please Confirm This Drawing On/Before
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. 9. RELIABILITY TEST The Reliability test items and its conditions are shown in below. High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Vibration test (nonoperating) Shock test (non-operating) Electro-static discharge test (operating) Ta = 50°C , 80%RH, 72 hrs Ta = 50°C , 60%RH, 72 hrs Ta = 0°C , 72 hrs Ta = -20 °C ↔ 60 °C (0.5 hr), 60%± 3%RH, 100 cycle Ta = 25°C , 60%RH, 1.5G, 10~500Hz, Sine X,Y,Z / Sweep rate : 1 hour Ta =...
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD. (11) To determine the optimum mounting angle, refer to the viewing angle range in the specification for each model. (12) If the customer's set presses the main parts of the LCD, the LCD may show the abnormal display. But this phenomenon does not mean the malfunction of the LCD and should be pressed by the way of mutual agreement. (13) Do not drop water or any chemicals onto the LCD’s surface. 10.1 Operating Precautions (1) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And...
Open the catalog to page 12All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
