Manufacturer Certificated Product Specification Model: TTX116BHT-01 11.6″ TFT Display Module (1920*1080) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. RECORDS OF REVISION DATE

TAILOR PIXELS TECHNOLOGY CO., LTD. 1. Application This specification applies to a color TFT-LCD Module, 2. Overview The TFT-LCD Module is a color active matrix TFT LCD FOB using amorphous silicon TFT's(Thin Film Transistors) as an active switching devices. This module has a 11.6 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is a low reflection and higher color type. The...

TAILOR PIXELS TECHNOLOGY CO., LTD. Outline dimensions Parameter Unit outline dimensions [Note 3-1]Outline dimensions is shown in page 17 [Note 3-2]Without war page and deflection. 4. Input Terminals 4-1 Driving interface of PWB CN1 (eDP signals, +3.3V DC power supply and B/L power supply) Pin No. High Speed round Complement Signal Link Lane 1 True Signal Link Lane 1 High Speed round Complement Signal Link Lane 0 True Signal Link Lane 0 High Speed round True Signal Auxiliary Channel Complement Signal Auxiliary Channel High Speed round

TAILOR PIXELS TECHNOLOGY CO., LTD. 15 LCD logic and driver ground LCD logic and driver ground Backlight ground Backlight ground Backlight ground Backlight ground Backlight on/off Backlight power Backlight power Vled Backlight power Backlight power *1 P: POWER I: Input O: Output Note ・ Don’t input any signals or any powers into a NC pin. Keep the NC pin open. ・ The shielding case is connected with signal GND. ・Connector used :20455-030E-76(I-PEX) ・Corresponding connector : 20453-030T (I-PEX) (Panda is not responsible to its product quality, if the user applies a connector not corresponding to...

TAILOR PIXELS TECHNOLOGY CO., LTD. 4-2 eDP interface Electrical Characteristics 5-1 Absolute Maximum Ratings Ratings Parameter Symbol Condition Input voltage(eDP) Storage temperature Operation temperature [Note 5-2] (*) “Absolute Maximum Ratings” is regulations that do not exceed it even momentarily. (*) Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. [Note 5-1] eDP signals [Note 5-2] Humidity: 90%RH Max.at Ta≦+40℃. Maximum wet-bulb temperature at +39℃ or less at Ta>+40℃

TAILOR PIXELS TECHNOLOGY CO., LTD. 5. DC Characteristics 5-2-1. TFT-LCD panel driving DC Electrical Characteristics Parameter Current dissipation Permissible input ripple voltage Differential Peak-to-peak Input Voltage at Rx package pins Power Consumption [Note 5-2-1] ON-OFF conditions for supply voltage

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. 7. Timing characteristics of input signals 7-1.Timing Characteristics The TFT-LCD Module is operated by the DE only. VDD=+3.3V~3.6V,Ta=-0~+60℃ 7-2. eDP Rx Interface Timing Parameter The specification of the eDP Rx interface timing parameter is shown

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. 7-3 Input sigal,basic display colors and gray scale of each color Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of 24 bit data signals, the 16.7M color display can be achieved on the screen. 8. EDID TBD

TAILOR PIXELS TECHNOLOGY CO., LTD. 9. Optical characteristics Paramete Contrast Ratio Response Time Green x CF Color Chromaticity (CIE1931) Center Luminance of white Cross Talk NTSC ratio measurement shall be taken 30 minutes after lighting the module at the following rating. ※Condition: PWM Duty = 100% ※The optical characteristics shall be measured in a dark room or equivalent.

TAILOR PIXELS TECHNOLOGY CO., LTD. [Note 9-3]Definitions of viewing angle range [Note 9-4]Definition of contrast ratio: The contrast ratio is defined as the following. Luminance(Brightness) with all pixels white Contrast Ratio = Luminance(Brightness) with all pixels Black [Note 9-5]Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white”.

TAILOR PIXELS TECHNOLOGY CO., LTD. [Note9-6]Thisshallbemeasuredatcenterofthescreen. [Note9-7]Definition of white uniformity : White uniformity is definedasthe Following with 5 measurements(A~M) Maximum Luminance of 5 Points(Brightness) δW = ———————————————————— Minimum Luminanceof 5 Points(Brightness) [Note9-7]Cross Modulation Test Description Where: Y A = Initial luminance of measured area (cd/m 2 ) Y B = Subsequent luminance of measured area (cd/m 2 ) The location measured will be exactly the same in both patterns Cross-Talk of one area of the LCD surface by another shall be measured by comparing...

TAILOR PIXELS TECHNOLOGY CO., LTD. element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged....