Manufacturer Certificated Product Specification Model: TTX101BVE-01 10.1″TFT Display Module (800*1280) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. Issued Date

TAILOR PIXELS TECHNOLOGY CO., LTD. Feature Size Resolution Interface Connect type Color Depth Technology type Display Spec. Pixel pitch (mm) Pixel Configuration Display Mode Driver IC Surface Treatment Viewing Direction LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Weight (g) LED Numbers Spec 10.1-inch 800(horizontal)*1280(Vertical) MIPI Connector 16.7M a-Si 0.1692*0.1692 R.G.B.-Vertical Stripe Normally Black HC ALL 228.6(W)X143(H)X2.6(D) 216.58(H)x135.36(V) Without TSP TBD 27 Note 1: Viewing direction is follow the data which measured by optics equipment. Note 2: Requirements on Environmental...

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. Power supply. Ground. MIPI differential data0- input MIPI differential data0+ input Ground. Reset pin,active “L” No connection. MIPI differential data2- input MIPI differential data2+ input Ground. MIPI differential data3- input MIPI differential data3+ input Ground. No connection. Ground. Ground. MIPI differential data1- input MIPI differential data1+ input Ground. MIPI differential CLK- input MIPI differential CLK+ input Ground.

TAILOR PIXELS TECHNOLOGY CO., LTD. 5 Absolute Maximum Ratings 5.1 Electrical Absolute Maximum Ratings.(Vss=0V ,Ta=25℃) Power Supply Voltage Notes: 1. If the module is above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also exceeded, the module will malfunction and cause poor reliability. 2. VDD >VSS must be maintained. 5.2 Environmental Absolute Maximum Ratings. Ambient Temperature Notes: 1. The response time will become lower when operated at low temperature. 2. Background color changes slightly...

TAILOR PIXELS TECHNOLOGY CO., LTD. 6 Electrical Characteristics 6.1 TFT LCD Module Parameter Power supply Input voltage 6.2 Timing characteristics 6.2.1 Power on/off Sequence Power ON

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.2.2 Data input format for MIPI

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.2.3 Input Timing Table 6.3 Driving Backlight Item Forward Current Forward Voltage Remark Note 1 Note 2 Note 3 Note 1: Each LED: IF =20 mA, VF =3.0V. Note 2: Optical performance should be evaluated at Ta=25℃ only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The lifetime of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating lifetime is estimated data.

TAILOR PIXELS TECHNOLOGY CO., LTD. 7 Optical Characteristics Items Viewing angles Symbol Condition Min. θT θB Center CR≥10 θL θR Contrast Ratio Response Time Green Blue White Uniformity Luminance Θ=0 Normal viewing angle Test Conditions: 1. IF= 20mA (one channel), the ambient temperature is 25°C. 2. The test systems refer to Note 1 and Note 2. Note 1: Definition of optical measurement system. The optical characteristics should be measured in the darkroom. After 5 minutes of operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must...

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 2: Definition of viewing angle range and measurement system. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Note 3: Definition of contrast ratio Note 4: Definition of Response time The output signals of photo detector are measured when the input signals are changed from “black” to “white” (rising time) and from “white” to “black” (falling time), respectively. Definition of response time：The response time is defined as the time interval between the 10% and 90% amplitudes

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the Center of each measuring area Luminance Uniformity (U) = Lmin/ Lmax X100% L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of Luminance:...

TAILOR PIXELS TECHNOLOGY CO., LTD. 8 Environmental / Reliability Tests No Test Item High Temperature Operation High Temperature Storage Low Temperature Storage High Temperature & Humidity Storage -20℃ 30 min ~ +60℃ 30 min Change time: 5min, 30 Cycle Thermal Shock (Non-operation) Electro Discharge (Operation) Vibration (Non-operation) Shock (Non-operation) Package Drop Test C=150pF, R=330 Ω, 5 points/panel Air:±8KV, 5 times; Contact: ±4KV, 5 times; (Environment: 15℃ ~ 35℃, 30% ~ 60%, 86Kpa ~ 106Kpa) Frequency range: 10~55Hz, Stroke: 1.mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of X.Y....

TAILOR PIXELS TECHNOLOGY CO., LTD. 9 Precautions For Use of LCD modules 9.1 Handling Precautions 9.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 9.1.4 The polarizer...