Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TTX080QHT-02 8.0″TFT Display Module (1024*768) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD. Issued Date First Release
Open the catalog to page 3
TAILOR PIXELS TECHNOLOGY CO., LTD. Feature Size Resolution Glass Maker Interface Connect type Color Depth Technology type Pixel pitch (mm) Pixel Configuration Display Mode Driver IC Viewing Direction Gray Scale Inversion Direction LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Weight (g) LED Numbers Spec 8.0-inch 1024(horizontal)*768(Vertical) Innolux LVDS Connector 16.7M a-Si 0.1583*0.1583 R.G.B. Stripe Normally Black TBD All FREE 174*136*2.5 162.05*121.54 Without 30LEDs Note 1: Viewing direction follows the data measured by optics equipment. Note 2: Requirements on Environmental...
Open the catalog to page 4
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 5
TAILOR PIXELS TECHNOLOGY CO., LTD. Common voltage 3.3V Power 3.3V Power Not connect Global reset pin Active low enter reset state Suggest connecting with an RC reset Normally pull high (R=100K, C=1UF) Standby mode, normally pull high STBYB=”1”, timing control, source driver will turn off, all output is high-Z System Ground Negative LVDS differential data input Positive LVDS differential data input System Ground Negative LVDS differential data input Positive LVDS differential data input System Ground Negative LVDS differential data input Positive LVDS differential data input System Ground...
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD. Vertical inversion Note3 Positive power for TFT Not connect Note2 Not connect Note2 Positive power for TFT Not connect Not connect 38 VGH 39 LED+ 40 LED+ I: input, O: output, P: Power Note1: If LVDS input data is 6 bits, selb must be set to High; If LVDS input data is 8 bits, selb must be set to Low. Note2: When CABC_EN=”00”, CABC OFF. When CABC_EN=”01”, user interface image. When CABC_EN=”10”, still picture. When CABC_EN=”11”, moving image. When CABC off, don’t connect DIMO, else connect it to backlight. Note3: When L/R=”0”, set right to left scan...
Open the catalog to page 7
TAILOR PIXELS TECHNOLOGY CO., LTD. 5 Absolute Maximum Ratings Item Power voltage Operating Temperature Storage Temperature Note 1: Be sure to apply VCC and VGL to the LCD first, and then apply VGH. Note 2: VCC setting should match the signals output voltage (refer to Note 3) of the customer’s system board. Note 3: Typical Vcom is only a reference value; it must be optimized according to each LCM, please use VR and base on the below application circuit. Note 4: Reset, stbyb, selb, L/R, U/D, cabcen0, cabcen 1.
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. 6 Electrical Characteristics 6.1 Operation Conditions Item Input signal voltage Input logic high voltage Input logic low voltage Power voltage Note 1: Be sure to apply VCC and VGL to the LCD first, and then apply VGH. Note 2: VCC setting should match the signals output voltage (refer to Note 3) of the customer’s system board. Note 3: Typical Vcom is only a reference value; it must be optimized according to each LCM, please use VR and base on the below application circuit. Note 4: Reset, stbyb, selb, L/R, U/D, cabcen0, cabcen 1. 6.2 5.2 Power ON.OFF...
Open the catalog to page 9
TAILOR PIXELS TECHNOLOGY CO., LTD. 6.3 Timing Characteristics 6.3.1 AC electrical characteristics
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. Input Clock and Data Timing Diagram
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 12
TAILOR PIXELS TECHNOLOGY CO., LTD. Data Input Format
Open the catalog to page 13
TAILOR PIXELS TECHNOLOGY CO., LTD. 6.4 Driving Backlight Item Forward Current Forward Voltage Note 1: Each LED: IF =15mA,VF=6.0V Note 2: Optical performance should be evaluated at Ta=25℃ only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The lifetime of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data.
Open the catalog to page 14
TAILOR PIXELS TECHNOLOGY CO., LTD. 7 Optical Characteristics Items Symbol Condition Min θT θB Center Viewing angles CR≥10 θL θR Contrast Ratio CR Θ =0 TON Response Time 25°C TOFF XW 0.26 Chromaticity White YW 0.28 Uniformity U 80 Luminance L Test Conditions: 1. IF= 60mA (one channel), the ambient temperature is 25°C. 2. The test systems refer to Note 1 and Note 2. Note 1: Definition of optical measurement system. The optical characteristics should be measured in the darkroom. After 5 minutes of operation, the optical properties are measured at the center point of the LCD screen. All input...
Open the catalog to page 15
TAILOR PIXELS TECHNOLOGY CO., LTD. Note 3: Definition of contrast ratio Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90% Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring...
Open the catalog to page 16
TAILOR PIXELS TECHNOLOGY CO., LTD. Luminance Uniformity (U) = Lmin/ Lmax X100% L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of Luminance: Measure the luminance of white state at center point.
Open the catalog to page 17
TAILOR PIXELS TECHNOLOGY CO., LTD. 8 Environmental / Reliability Tests No Test Item High Temperature Operation High Temperature Storage Low Temperature Storage High Temperature & Humidity Storage -30℃ 30 min ~ +80℃ 30 min Change time: 5min, 30 Cycle Thermal Shock (Non-operation) Electro Discharge (Operation) Vibration (Non-operation) Shock (Non-operation) Package Drop Test C=150pF, R=330 Ω, 5 points/panel Air:±8KV, 5 times; Contact: ±4KV, 5 times; (Environment: 15℃ ~ 35℃, 30% ~ 60%, 86Kpa ~ 106Kpa) Frequency range: 10~55Hz, Stroke: 1.mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of...
Open the catalog to page 18All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
