Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TTX070BHE-01 7.0″TFT Display Module (800*480) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 2
TAILOR PIXELS TECHNOLOGY CO., LTD. Issued Date First Release.
Open the catalog to page 3
TAILOR PIXELS TECHNOLOGY CO., LTD. Feature Size Resolution Interface Connect type Color Depth Technology type Display Spec. Pixel pitch (mm) Pixel Configuration Display Mode Driver IC Surface Treatment Viewing Direction LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Weight (g) LED Numbers Spec 7-inch 800(horizontal)*480(Vertical) 24-bit RGB Connector 16.7M a-Si 0.192 x 0.1805 R.G.B. Vertical Stripe Normally White EK9716BD4+EK73002AB2 HC 12 O’clock 164.90*100*3.5 154.08 x 85.92 WithOut TSP TBD 24LEDs Note 1: Viewing direction is follow the data which measured by optics equipment....
Open the catalog to page 4
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 5
TAILOR PIXELS TECHNOLOGY CO., LTD. Symbol LEDK LEDA GND VDD R0~R7 G0~G7 B0~B7 GND DCLK DISP HSYNC VSYNC DE NC GND XR(NC) YD(NC) XL(NC) YU(NC) Description Power for LED backlight cathode Power for LED backlight anode Ground Power supply Data bus Data bus Data bus Ground Pixel clock Display on/ off Horizontal sync Signal Vertical sync signal Data Enable No connected System Ground The right side signal pin of TP The bottom side signal pin of TP The left side signal pin of TP The top side signal pin of TP Absolute Maximum Ratings Item Supply Voltage Operating Temperature Storage Temperature
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD. 6 Electrical Characteristics 6.1 Driving TFT LCD Panel
Open the catalog to page 7
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. 6.3 Driving Backlight Item Forward Current Forward Voltage Note 1: Each LED: IF =20 mA Note 2: Optical performance should be evaluated at Ta=25℃ only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The lifetime of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating lifetime is estimated data.
Open the catalog to page 9
TAILOR PIXELS TECHNOLOGY CO., LTD. 7 Optical Characteristics Items Viewing angles Contrast Ratio Response Time White Symbol Condition Min. θT θB Center CR≥10 θL θR CR TON TOFF XW YW XR YR XG YG XB YB Test Conditions: 1. IF= 20mA (one channel), the ambient temperature is 25°C. 2. The test systems refer to Note 1 and Note 2. Note 1: Definition of optical measurement system. The optical characteristics should be measured in the darkroom. After 5 minutes of operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when...
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. Note 2: Definition of viewing angle range and measurement system. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Note 3: Definition of contrast ratio Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the Center of each measuring area Luminance Uniformity (U) = Lmin/ Lmax X100% L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of...
Open the catalog to page 12
TAILOR PIXELS TECHNOLOGY CO., LTD. 8 Environmental / Reliability Tests No Test Item High Temperature Operation High Temperature Storage Low Temperature Storage High Temperature & Humidity Storage -20℃ 30 min ~ +60℃ 30 min Change time: 5min, 30 Cycle Thermal Shock (Non-operation) Electro Discharge (Operation) Vibration (Non-operation) Shock (Non-operation) Package Drop Test C=150pF, R=330 Ω, 5 points/panel Air:±8KV, 5 times; Contact: ±4KV, 5 times; (Environment: 15℃ ~ 35℃, 30% ~ 60%, 86Kpa ~ 106Kpa) Frequency range: 10~55Hz, Stroke: 1.mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of...
Open the catalog to page 13
TAILOR PIXELS TECHNOLOGY CO., LTD. 9 Precautions For Use of LCD modules 9.1 Handling Precautions 9.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 9.1.4 The...
Open the catalog to page 14All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
