Manufacturer Certificated Product Specification Model: TTX050BHS-01 5.0″TFT Display Module (480*272) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. Issued Date First Release.

TAILOR PIXELS TECHNOLOGY CO., LTD. Feature Size Resolution Interface Connect type Color Depth Technology type Pixel pitch (mm) Pixel Configuration Display Mode Driver IC Viewing Direction GSI Direction LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Weight (g) LED Numbers Spec 5-inch 480(horizontal)*272(Vertical) 24bit-RGB Connector 16.7M a-Si 0.231 x 0.231 R.G.B. Vertical Stripe Normally White 12 O’clock 6 O’clock 120.7*75.8*3 110.88 x62.83 Without TBD 12 LEDs Note 1: Viewing direction is follow the data which measured by optics equipment. Note 2: Requirements on Environmental Protection:...

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. LEDK LEDA GND VDD R0~R7 G0~G7 B0~B7 DGND DCLK DISP HSYNC VSYNC DE NC GND XR YD XL YU Description Backlight LED Cathode Backlight LED Anode. Ground Power supply Data bus Data bus Data bus Ground Dot clock signal input. Latching input data at its rising edge. Standby mode. Normally pulled high. DISP=“1”: Normally operation (Default) DISP=“0”: Timing controller, source driver will turn off ,all output are High-Z. Horizontal sync input. Negative polarity. Vertical sync input. Negative polarity. Data enable input. Active high to enable the input data bus under “DE...

TAILOR PIXELS TECHNOLOGY CO., LTD. 5 Absolute Maximum Ratings Item Supply Voltage Operating Temperature Storage Temperature 6 Electrical Characteristics 6.1 Driving TFT LCD Panel Supply Voltage High Level Input Signal Voltage 6.2 Driving Backlight Item Forward Current Forward Voltage Note 1: Each LED: IF =20 mA Note 2: Optical performance should be evaluated at Ta=25℃ only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The lifetime of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating lifetime...

TAILOR PIXELS TECHNOLOGY CO., LTD. Source+Gate Driver 5 inch 480(RGB )*272 Grayscale Manipulation Voltage 6.4 Interface Timing 6.4.1 Timing relationship among DE, Source Output, Gate Output, Vcom Output Timing Diagram

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.4.2 Parallel RGB Data Format

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.4.3 Clock and Data Input Waveforms

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.4.4 Data Input Format

TAILOR PIXELS TECHNOLOGY CO., LTD. 7 Optical Characteristics Items Viewing angles Symbol Condition Min. θT θB Center CR≥10 θL θR - Contrast Ratio Response Time Color Chromaticity Uniformity NTSC Luminance Test Conditions: 1. IF= 20mA (one channel), the ambient temperature is 25. 2. The test systems refer to Note 1 and Note 2. Note 1: Definition of optical measurement system. The optical characteristics should be measured in the darkroom. After 5 minutes of operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring...

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 2: Definition of viewing angle range and measurement system. viewing angle is measured at the center point of the LCD by CONOSCOPE(ergo-80). Note 3: Definition of contrast ratio “White state “: The state is that the LCD should driven by Vwhite. “Black state”: The state is that the LCD should driven by Vblack. Vwhite: To be determined Vblack: To be determined. Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector...

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the Center of each measuring area. Luminance Uniformity(U) = Lmin/ Lmax X100% L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of Luminance:...

TAILOR PIXELS TECHNOLOGY CO., LTD. 8 Environmental / Reliability Tests No Test Item High Temperature Operation High Temperature Storage Low Temperature Storage High Temperature & Humidity Storage -30℃ 30 min ~ +80℃ 30 min Change time: 5min, 30 Cycle Thermal Shock (Non-operation) Electro Discharge (Operation) Vibration (Non-operation) Shock (Non-operation) Package Drop Test C=150pF, R=330 Ω, 5 points/panel Air:±8KV, 5 times; Contact: ±4KV, 5 times; (Environment: 15℃ ~ 35℃, 30% ~ 60%, 86Kpa ~ 106Kpa) Frequency range: 10~55Hz, Stroke: 1.mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of X.Y....

TAILOR PIXELS TECHNOLOGY CO., LTD. 9 Precautions For Use of LCD modules 9.1 Handling Precautions 9.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 9.1.4 The polarizer...