Manufacturer Certificated Product Specification Model: TTX035BHS-01 3.5″TFT Display Module (320*240) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. 1 Record of Revision Version Revise Date First Release.

TAILOR PIXELS TECHNOLOGY CO., LTD. Feature LCD Size Display Format Interface Color Depth Technology type Display Spec. Display Mode Driver IC Surface Treatment Viewing Direction Gray Viewing Direction LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Weight (g) LED Numbers Spec 3.5inch 320 (RGB) × 240 24-bit RGB 16.7M a-Si 0.073 x 0.219 Normally BLACK ST7272A Haze 20% ALL FREE 76.90*63.9*3.26 70.08 x 52.56 Without TSP TBD 6 LEDs Note 1: Viewing direction is following the data which measured by optics equipment. Note 2: Requirements on Environmental Protection: RoHS Note 3: LCM weight tolerance:...

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. VBLVBL+ YU XR NC RESET SPENB SPCK SPDA B0~B7 G0~G7 R0~R7 HSYNC VSYNC DOTCLK NC VDD YD XL NC IF2 IF1 IF0 NC DEN GND Backlight LED Cathode Backlight LED Anode. Touch panel up side Touch panel right side NC Reset Signal pin (“Low” is enable) Chip select Serial Clock. Serial Data Data bus Data bus Data bus Line Synchronous Signal Frame Synchronous Signal Dot-clock signal and oscillator source NC Power supply for logic operation Touch panel bottom side Touch panel left side Control the input data format/floating Control the input data format Control the input data...

TAILOR PIXELS TECHNOLOGY CO., LTD. 5 Absolute Maximum Ratings Item Supply Voltage Operating Temperature Storage Temperature 6 Electrical Characteristics 6.1 Driving TFT LCD Panel Analog Supply Voltage High Level Input Signal Voltage

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.2 Driving Backlight Item Forward Current Forward Voltage Note 1: Each LED: IF =20 mA/LED VF=6.0V Note 2: Optical performance should be evaluated at Ta=25℃ only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The lifetime of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating lifetime is estimated data. Figure: LED connection of backlight

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. 6.4 Parallel 24bit RGB Input Timming Table 6.5 Serial 8bit RGB Input Timming Table

TAILOR PIXELS TECHNOLOGY CO., LTD. 7 Optical Characteristics Items Viewing angles Contrast Ratio Response Time White Symbol Condition Min. θT θB Center CR≥10 θL θR CR TON TOFF XW YW XR YR XG YG XB YB U NTSC Luminance Test Conditions: 1. IF= 20mA(one channel),the ambient temperature is 25°C. 2. The test systems refer to Note 1 and Note 2. Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical Properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when...

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 2: Definition of viewing angle range and measurement system. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Note 3: Definition of contrast ratio Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval Between “White” state and “Black” state. Rise time (TON) is the time between Photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is The time between photo detector output intensity changed from 10% to 90%

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the Center of each measuring area Luminance Uniformity (U) = Lmin/ Lmax X100% L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of Luminance:...

TAILOR PIXELS TECHNOLOGY CO., LTD. 8 Environmental / Reliability Tests No Test Item High Temperature Operation High Temperature Storage Low Temperature Storage High Temperature & Humidity Storage -30℃ 30 min ~ +80℃ 30 min Change time: 5min, 30 Cycle Thermal Shock (Non-operation) Electro Discharge (Operation) Vibration (Non-operation) Shock (Non-operation) Package Drop Test C=150pF, R=330 Ω, 5 points/panel Air:±6KV, 5 times; Contact: ±2KV, 5 times; (Environment: 15℃ ~ 35℃, 30% ~ 60%, 86Kpa ~ 106Kpa) Frequency range: 10~55Hz, Stroke: 1.mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of X .Y....

TAILOR PIXELS TECHNOLOGY CO., LTD. 9.Precautions For Use of LCD modules 9.1 Handling Precautions 9.1.1The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 9.1.4 The polarizer...