Catalogs >
TAILOR PIXELS TECHNOLOGY CO., LTD. >
Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960)

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960)
21Pages

Catalog excerpts

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 1

Manufacturer Certificated Product Specification Model: TTH371BVS-01 3.71″TFT Display Module (240*960) This module uses ROHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

Open the catalog to page 1

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 2

TAILOR PIXELS TECHNOLOGY CO., LTD. Records of Revision 修改记录 Rev

Open the catalog to page 2

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 3

TAILOR PIXELS TECHNOLOGY CO., LTD.

Open the catalog to page 3

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 4

TAILOR PIXELS TECHNOLOGY CO., LTD. General Description 规格简介 This display module is a transmissive type color active matrix TFT(Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This module is composed of a TFT LCD module, a driver circuit, and a back-light unit.The resolution of a 3.71” contains 240RGB x 960 dots and can display up to 16.7M colors. 该显示模块是一种采用非晶硅 TFT 作为开关器件的透射型彩色有源矩阵 TFT(薄膜晶体管)液晶显示器。该模块由 TFT 液晶显示模块、驱动电路和背光单元组成。3.71 英寸的分辨率包含 240RGB x 960 点，可显示高达 16.7M 的颜色。 Module Parameter 模组参数 Features Display Size(Diagonal) 显示尺寸(对角线)...

Open the catalog to page 4

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 5

TAILOR PIXELS TECHNOLOGY CO., LTD. 240*RGB*960 DOTS VIEWING DIRECTION:ALL 白色对位丝印线 IC与元件区域点黑色热固胶,点胶不能超过IC高度，器件区要贴黑色绝缘胶，黑色古川FT25BT 厚度0.05mm. IC与元件区域点黑色热固胶,点胶不能超过IC高度，器件区要贴黑色绝缘胶，黑色古川FT25BT 厚度0.05mm. 高温胶带+IC元器件 +FPC+补强+导电布元件区域0.8MAX 需覆黄色绝缘胶 TOUCH-FPC DISPLAY-FPC 01 V LED_P 02 V LED_P 03 V LED_N 04 V LED_N 05 GND 06 V IO2V8_ PMU 07 V IO1V8_ PMU 08 GND 09 DSI_TE 10 LC

Open the catalog to page 5

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 6

TAILOR PIXELS TECHNOLOGY CO., LTD. Module Interface 模组接口定义 SYMBOL LEDA Power Supply for Analog, VDD=2.4V~3.3V. Power Supply for I/O system. VDDIO=1.65V~3.3V Power Ground This signal will reset the device and it must be applied to properly initialize the chip Power Ground Power Ground High speed interface data differential signal input/output pins. High speed interface data differential signal input/output pins. Power Ground High speed interface data differential signal input/output pins. High speed interface data differential signal input/output pins. Power Ground Power Supply for Touch...

Open the catalog to page 6

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 7

TAILOR PIXELS TECHNOLOGY CO., LTD. recommend a backlight driving circuit is best rated current.It is recommended to use IC (AW9364). The reference circuit is as follows： 5.2Backlight recommended circuit 背光电路参数推荐 Motherboard driver backlight is need constant current circuit: 4 灯串联 Note: constant current circuit for every LED,and though LED lamp current is less than 20mA.Recommand between 15mA and 20 mA for every LED. 5.3 Application Circuit

Open the catalog to page 7

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 8

TAILOR PIXELS TECHNOLOGY CO., LTD. 6 Absolute Maximum Ratings 绝对最大额定值 VSS=0V, Ta=25ºC Item 项目 Power supply 电力供应 Supply Voltage 电源电压 Analog 模拟 IO Input Voltage 输入电压 Storage temperature 储存温度 Symbol VDD IOVDD Vi Tstg Operating temperature 工作温度 Storage humidity 存储湿度 Operating humidity 操作湿度 Note 1: 90%RH max, If Ta is below 50ºC; 60%RH max, If Ta is over 60ºC. Electrical Specification 电性规格 DC Characteristics 直流特性 Item 项目 Powersupply 电力供应 Supply Voltage 电源电压 Analog IO Logic Low input voltage 输入电压低 Logic High input voltage 输入电压高 Logic Low output voltage 输出电压低 Logic High output voltage 输出电压高 Normal...

Open the catalog to page 8

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 9

TAILOR PIXELS TECHNOLOGY CO., LTD.

Open the catalog to page 9

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 10

TAILOR PIXELS TECHNOLOGY CO., LTD.

Open the catalog to page 10

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 11

TAILOR PIXELS TECHNOLOGY CO., LTD. Optical Specifications 光学规格 9.1 Optical Specifications 光学规格

Open the catalog to page 11

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 12

TAILOR PIXELS TECHNOLOGY CO., LTD. Luminance on surface( I f =20mA) 表面亮度 Backlight On (Transmissive Mode) Contrast ratio 对比度 Response time 响应时间 Normally viewing angle  X = Y =0º Vertical NTSC Ratio(Gamut) 9.2

Open the catalog to page 12

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 13

TAILOR PIXELS TECHNOLOGY CO., LTD. Definition of Contrast Ratio 对比度的定义 Contrast is measured perpendicular to display surface in reflective and transmissive mode. The measurement condition is: Measuring Equipment 测量设备 Measuring Point Diameter 测点直径 Measuring Point Location 测点位置 Active Area centre point A: All Pixels white B: All Pixel black Maximum Test pattern 测试模式 Contrast setting Definitions: CR (Contrast) = Luminance of White Pixel / Luminance of Black Pixel 9.4 Definition of Viewing Angles Measuring machine: LCD-5100 or EQUI 9.5 Definition of Color Appearance 色域的定义 R,G,B and W are...

Open the catalog to page 13

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 14

TAILOR PIXELS TECHNOLOGY CO., LTD. Quality Assurance 质量标准 10.1 This standard for Quality Assurance assures the quality of LCD module products supplied to customer by Tailorpixels . 10.2 Agreement Items 协议项目 Tailorpixels and customer shall negotiate if the following situation occurs: 10.2.1 Discrepancies between Tailorpixels ’s QA standards and customer’s QA standards. 10.2.2 Additional requirement to be added in product specification. 10.2.3 Any other special problem. 10.3 Standard of the Product Visual Inspection 产品外观检验标准 10.3.1 Appearance inspection: 10.3.1.1 The inspection must be under...

Open the catalog to page 14

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 15

TAILOR PIXELS TECHNOLOGY CO., LTD. Black / White spot Foreign material (Round type) Pinholes Stain 01 Particles inside cell. (Minor defect) 黑/白孔染色颗粒。 (小瑕疵) Distance between 2 defects should more than10mm apart. Black and White line Scratch Foreign material (Line type) (Minor defect) 黑白线刮伤异物(类型)行 (小瑕疵) Distance between 2 defects should more than 10mm apart. Scratches not viewable through the back of the display are acceptable. Glass Crack (Minor defect) 玻璃裂纹(小瑕疵) LCD with extensible crack line is unacceptable(When press the cracked LCD area, the line will expand, we define it is...

Open the catalog to page 15

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 16

TAILOR PIXELS TECHNOLOGY CO., LTD. Glass Chipping Rear of PadArea:(Minordefect ) 玻璃切屑垫区后方: 05

Open the catalog to page 16

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 17

TAILOR PIXELS TECHNOLOGY CO., LTD. Item 项目 Glass Burr: (Minor defect) 玻璃 Criteria (Unit: mm) 标准 Glass burr don’t affect assemble and module dimension. FPC Defect: (Minor defect) FPC 缺陷:(小瑕疵) a 9.1 Dent, pinhole width a

Open the catalog to page 17

Product Specification Model:TTH371BVS-01 3.71″ TFT Display Module (240*960) - 18

TAILOR PIXELS TECHNOLOGY CO., LTD. D: Diameter W: width L: length 14.1 Spot: D≤0.20 is acceptable 0.200.3 is unacceptable 14.2 Dent（dot): D≤0.20 is acceptable 0.200.30 is unacceptable 2dots are acceptable and the distance between defects should more than 10 mm. Dent（line) According to the limit sample 14.3 Scratch: W≤0.03, L≤10 is acceptable, 0.030.10 is unacceptable. Distance between 2 defects should more than 10 mm. 15.1 No distortion or contamination on PCB terminals. 15.2 All components on PCB must same as documented on the BOM/component layout. 15.3 Follow IPC-A-600F. (Major defect) 电气...

Open the catalog to page 18