Manufacturer Certificated Product Specification Model: TTH146BVS-01 1.46″TFT Display Module (172*320) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. Records of Revision 修改记录 Rev

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. General Description 规格简介 This display module is a transmissive type color active matrix TFT(Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This module is composed of a TFT LCD module, a driver circuit, and a back-light unit.The resolution of a 1.46” contains 172RGB x 320 dots and can display up to 262K colors. 该显示模块是一种采用非晶硅 TFT 作为开关器件的透射型彩色有源矩阵 TFT(薄膜晶体 管)液晶显示器。该模块由 TFT 液晶显示模块、驱动电路和背光单元组成。1.46 英寸的分辨率 包含 172RGB x 320 点，可显示高达 262K 的颜色。 Module Parameter 模组参数 Features Display Size(Diagonal) 显示尺寸(对角线) LCD...

TAILOR PIXELS TECHNOLOGY CO., LTD. LED CIRCUIT DIAGRAM: LEDA

TAILOR PIXELS TECHNOLOGY CO., LTD. Module Interface 模组接口定义 Power Supply for Analog Power Grounde Power Grounde SPI interface input/output pin.the data is latched on the rising edge of the SCL signal This pin is used to be serial interface clock Power Supply for Analog This signal will reset the device and it must be applied to properly initialize the chip.Signal is active low Chip selection pin;Low enable,high disable Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin Data/command...

TAILOR PIXELS TECHNOLOGY CO., LTD. 5.3 Application Circuit 应用电路（） 6 Absolute Maximum Ratings 绝对最大额定值 VSS=0V, Ta=25ºC Item 项目 Power supply 电力供应 Supply Voltage 电源电压 Analog 模拟 IO Input Voltage 输入电压 Storage temperature 储存温度 Symbol VDD IOVDD Vi Tstg Operating temperature 工作温度 Storage humidity 存储湿度 Operating humidity 操作湿度 Note 1: 90%RH max, If Ta is below 50ºC; 60%RH max, If Ta is over 60ºC. Electrical Specification 电性规格 DC Characteristics 直流特性 Item 项目 Powersupply 电力供应 Supply Voltage 电源电压 Analog IO Logic Low input voltage 输入电压低 Logic High input voltage 输入电压高 Logic Low output voltage 输出电压低 Logic High...

TAILOR PIXELS TECHNOLOGY CO., LTD. Initialization Code 初始化代码

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. Optical Specifications 光学规格 9.1 Optical Specifications 光学规格 Backlight On (Transmissive Mode) surface( I f =20mA) 表面亮度 Contrast ratio 对比度 Response time 响应时间 Normally viewing angle  X = Y =0º Vertical NTSC Ratio(Gamut) 9.

TAILOR PIXELS TECHNOLOGY CO., LTD. Definition of Contrast Ratio 对比度的定义 Contrast is measured perpendicular to display surface in reflective and transmissive mode. The measurement condition is: Measuring Equipment 测量设备 Measuring Point Diameter 测点直径 Measuring Point Location 测点位置 Active Area centre point A: All Pixels white B: All Pixel black Maximum Test pattern 测试模式 Contrast setting Definitions: CR (Contrast) = Luminance of White Pixel / Luminance of Black Pixel 9.4 Definition of Viewing Angles Measuring machine: LCD-5100 or EQUI 9.5 Definition of Color Appearance 色域的定义 R,G,B and W are defined...

TAILOR PIXELS TECHNOLOGY CO., LTD. Quality Assurance 质量标准 10.1 This standard for Quality Assurance assures the quality of LCD module products supplied to customer by Tailorpixels . 10.2 Agreement Items 协议项目 Tailorpixels and customer shall negotiate if the following situation occurs: 10.2.1 Discrepancies between Tailorpixels ’s QA standards and customer’s QA standards. 10.2.2 Additional requirement to be added in product specification. 10.2.3 Any other special problem. 10.3 Standard of the Product Visual Inspection 产品外观检验标准 10.3.1 Appearance inspection: 10.3.1.1 The inspection must be under illumination...

TAILOR PIXELS TECHNOLOGY CO., LTD. Foreign material (Round type) Pinholes Stain Particles Black / White spot inside cell. (Minor defect) 黑/白斑/异物 (圆类型)细胞内的针孔 染色颗粒。(小瑕疵) Distance between 2 defects should more than10mm apart. Black and White line Scratch Foreign material (Line type) (Minor defect) 黑白线 刮伤异物(类型)行(小瑕 疵) Distance between 2 defects should more than 10mm apart. Scratches not viewable through the back of the display are acceptable. Glass Crack (Minor defect) 玻璃裂纹 (小瑕疵) LCD with extensible crack line is unaccept

TAILOR PIXELS TECHNOLOGY CO., LTD. Glass Chipping Pad Area: (Minor defect) 玻 璃碎片面积:(轻微缺陷) 04 Glass Chipping Rear of PadArea:(Minordefect) 玻璃切屑垫区后方: 05

TAILOR PIXELS TECHNOLOGY CO., LTD. FPC Defect: (Minor defect) FPC 缺 陷:(小瑕疵) a 9.1 Dent, pinhole width a

TAILOR PIXELS TECHNOLOGY CO., LTD. Touch Panel 触控面板 Criteria (Unit: mm) 标准 D: Diameter W: width L: length 14.1 Spot: D≤0.20 is acceptable 0.200.3 is unacceptable 14.2 Dent（dot): D≤0.20 is acceptable 0.200.30 is unacceptable 2dots are acceptable and the distance between defects should more than 10 mm. Dent（line) According to the limit sample 14.3 Scratch: W≤0.03, L≤10 is acceptable, 0.030.10 is unacceptable. Distance between 2 defects should more than 10 mm. 15.1 No distortion or contamination on PCB terminals. 15.2 All components on PCB must same as documented on the BOM/component layout. 15.3...

TAILOR PIXELS TECHNOLOGY CO., LTD. Classification of Defects 缺陷的分类 Visual defects (Except no / wrong label) are treated as minor defect and electrical defect is major. 10.6 Identification/marking criteria 识别/评分标准 Any unit with illegible / wrong /double or no marking/ label shall be rejected. 10.7 10.7.1 There should be no damage of the outside carton box, each packaging box should has label in the correct location per packing drawing requirement. 10.7.2 All direct package materials shall offer ESD protection. Reliability Specification 可靠性规范 Item Cycle Time Constant Temp. and Constant Humidity...