Manufacturer Certificated Product Specification Model: TTH040BRT-02C 4.0″TFT Display Module (720*720) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.

TAILOR PIXELS TECHNOLOGY CO., LTD. REVISION HISTORY GENERAL INFORMATION ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS TIMING CHARACTERISTICS BACKLIGHT CHARACTERISTICS EXTERNAL DIMENSIONS INTERFACE SIGNALS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION CRITERION PRECAUTINGS FOR USING LCD MODULES

TAILOR PIXELS TECHNOLOGY CO., LTD. 1 REVISION HISTORY Version First Issued

TAILOR PIXELS TECHNOLOGY CO., LTD. 2 GENERAL INFORMATION Item LCD size Display Mode Unit inch Normally Black Pixel pitch Pixel Arrangement 像素排列 Module outline dimension 液晶显示区域 触摸可视区域 Surface hardness 表面硬度 Touch function 触摸功能 Touch structure 触摸结构

TAILOR PIXELS TECHNOLOGY CO., LTD. ABSOLUTE MAXIMUM RATINGS Parameter AGND = GND = 0V, Ta = 25℃ Max. Unit. Note Power Supply voltage 1 Power Supply voltage 2 Operating temperature Storage temperature Tstg -30 +80 ℃ * The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. 4 ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS Parameter Supply voltage for analog Supply...

TAILOR PIXELS TECHNOLOGY CO., LTD. Parameter THS-PREPARE THS-TRAIL THS-EXIT Description Time that the transmitter drives the Data Lane LP-00 Line state immediately before the HS-0 Line state starting the HS transmission. THS-PREPARE + time that the transmitter drives the HS-0 state prior to transmitting the Sync sequence. Transmitted time interval from the start of THS-TRAILor TCLK-TRAIL, to the start of the LP-11 state following a HS burst. Time that the transmitter drives the flipped differential state after last payload data bit of a HS transmission burst. Time that the transmitter drives...

TAILOR PIXELS TECHNOLOGY CO., LTD. Table 5.1.2 Global Operation Timing Parameters for Clock Lane Figure 5.1.3 Turnaround timing sequence 5.2 High speed data-clock timing Figure 5.2.1 DDR clock definition

TAILOR PIXELS TECHNOLOGY CO., LTD. Table 5.2 Reverse HS data transmission timing parameters Figure 5.2.2 Data to clock timing definitions 5.3 Data-clock timing specifications Parameter Data to Clock Setup Time [Receiver] Clock to Data Hold Time [Receiver] Note：(1) Total setup and hold window for receiver of 0.3*UIINST. (2) 0.15UI is only for reference, related to the signal jitter caused by the transmittion path, this spec need to check on panel performance to fine tune. Table 5.3 Data to clock timing specifications

TAILOR PIXELS TECHNOLOGY CO., LTD. Figure 5.3 Skew window of transmittor and receiver 5.4 VDD VDDI Input power sequence VDD/VDDI input power on sequence VDD/VDDI input power off sequence

TAILOR PIXELS TECHNOLOGY CO., LTD. Notes: 1. The reset cancel includes also required time for loading ID bytes, VCOM setting and other settings from NVM (or similar device) to registers. This loading is done every time when there is HW reset cancel time (tRT) within 5 ms after a rising edge of RESX. 2. Spike due to an electrostatic discharge on RESX line does not cause irregular system reset according to the table below: RESX Pulse Reset Rejected Reset starts 3. During the Resetting period, the display will be blanked (The display is entering blanking sequence, which maximum time is 120 ms, when...

TP-FPC建议尺寸形状， 若空间不够，可往箭头 方向加长 1. Display ：4.0" 2. Resolution: 720xRGBx720 3. View Direction: ALL 4. LCD Driver:JD9365DA 5. *:Critical dimension ( ): Reference dimension; 6. Undefinition Tolerance:±0.2 7. OPERATING TEMP: -20°C~ +70°C 8. STORAGE TEMP: -30°C~ +80°C 9. Requirements on Environmental Protection: ROHS SILK BLACK

TAILOR PIXELS TECHNOLOGY CO., LTD. LEDA LEDK LEDK VCI IOVCC RST TE LED backlight anode LED backlight cathode LED backlight cathode Power supply for the analog power Power supply for the logic power and I/O circuit Reset signal(low active) Tearing effect output The PWM frequency output for LCD driver control. Power ground MIPI-DSI data lane 0 posivtve input pin MIPI-DSI data lane 0 negtive input pin Power ground MIPI-DSI data lane 1 posivtve input pin MIPI-DSI data lane 1 negtive input pin Power ground MIPI-DSI data lane posivtve input pin MIPI-DSI data lane negtive input pin Power ground MIPI-DSI...

TAILOR PIXELS TECHNOLOGY CO., LTD. 9 ELECTRO-OPTICAL CHARACTERISTICS Item Contrast ratio Response time Viewing angle range Red Green CIE(x,y) chromaticity Blue White Viewing normal angle Θx=θy=0° Ta=25℃ Note 1.Ambient condition：25℃±2℃，60±10%RH，under 10 Lunx in the darkroom。 Note 2.Measure device：BM-7A (TOPCON)，viewing cone=2° Lv = Average Surface Luminance with all white pixels (P1,P2,P3,P4,P5) Note 3. Definition of Contrast Ratio： Average Surface Luminance with all black pixels (P1,P2,P3,P4,P5) CR = Average Surface Luminance wit

TAILOR PIXELS TECHNOLOGY CO., LTD. Note 4. Definition of Response Time (Ton, Toff ), The response time is defined as the time interval between the 10% and 90% amplitudes. Note 5. Definition of view angle(θ，ψ)： Note 6. The LCD module should be stabilized at a given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room. Measouring method for Contrast ratio, surface luminance, Luminance uniformity,CIE(x,y) chromaticity. Light spot size ∅=7mm,...

TAILOR PIXELS TECHNOLOGY CO., LTD. 10 RELIABILITY TEST Reliability test conditions ( Polarizer characteristics null ) No. 1 2 3 4 5 Items High Temperature Storage Low Temperature Storage High Temperature Operating Low Temperature Operating High Temp. and High Humidity Storage Thermal Shock Dropping test (non-operation) Packing Vibration (non-operation) Inspection after test T = 80℃for 96 hr T = -30℃for 96 hr T = 70℃for 48 hr T = -20℃for 48 hr (But no condensation of dew) T = 60℃/90% for 96 hr (But no condensation dew) -20±2℃~25~60±2℃×10cycles (30min.) (5min.) (30min.) Drop to the ground from...