Manufacturer Certificated Product Specification Model: TOX096KSWEG01 0.96″ PM OLED Display Module (128*64) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd

TAILOR PIXELS TECHNOLOGY CO., LTD. Rev ised Hist ory vi to r Part Number

TAILOR PIXELS TECHNOLOGY CO., LTD.

TAILOR PIXELS TECHNOLOGY CO., LTD. 1. B asic Specificat ions Ba ti ns 1.1 Display Specifications 1) 2) 3) Display Mode: Display Color: Drive Duty: Passive Matrix Monochrome (White) 1/64 Duty Outline Drawing: Number of Pixels: Panel Size: Active Area: Pixel Pitch: Pixel Size: Weight: According to the annexed outline drawing 128  64 26.70  19.26  1.4 (mm) 21.744  10.864 (mm) 0.17  0.17 (mm) 0.154  0.154 (mm) 1.54 (g) 1.3 Active Area / Memory Mapping & Pixel Construction

Color: White Driver IC: SSD1306 FPC Number: XFP1306-01 Interface: 8-bit 68XX/80XX Parallel, 3-/4-wire SPI, I2C 5. General Tolerance: ±0.30 10.864 (A/A) 12.864 (V/A) 14.4±0.2 (Polarizer) 15.4±0.2 (Cap Size) 19.26±0.2 (Panel Size) Contact Side Customer Approval Signature 2-R0.4 mm Tolerance Dimension ±0.3 Angle ±1 General Roughness Unless Otherwise Specified TOX096KSWEG01 Folding Type OEL Display Module Pixel Number: 128 x 64, Monochrome, COG Package Drawing Number Contact Side 26.7±0.2 (Panel Size) 26.7±0.2 (Cap Size) 25.7±0.2 (Polarizer) 23.744 (V/A) 21.744 (A/A) TAILOR PIXELS TECHNOLOGY CO.,...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.5 Po wer Sup ply for Lo gic ow pp l og This is a voltage supply pin. It must be connected to external source. Grou nd of Lo gic Circ uit un d og cu This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. Po wer Sup ply for O EL Pan el ow pp l OE ne This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. Grou nd of Ana log Circ uit un d al...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.5 Pin Definition (Continued) Pin Number Read/ Write Se le ct o r Write /W elec or This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial or I2C mode is selected, this pin must be connected to VSS. H ost D ata Input/Ou tput...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.6 Block Diagram 1.6.1 VCC Supplied Externally Active Area 0.96" 128 x 64 Pixels MCU Interface Selection: BS0, BS1 and BS2 Pins connected to MCU interface: CS#, RES#, D/C#, R/W#, E/RD#, and D0~D7 C1, C3: 0.1μF C2: 4.7μF C4, C5: 4.7μF / 16V X7R R1: 910kΩ, R1 = (Voltage at IREF - VSS) / IRE

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.6.2 VCC Generated by Internal DC/DC Circuit Active Area 0.96" 128 x 64 Pixels MCU Interface Selection: BS0, BS1 and BS2 Pins connected to MCU interface: CS#, RES#, D/C#, R/W#, E/RD#, and D0~D7 C1, C2: 1μF C3: 2.2μF C4: 4.7μF / 16V X7R C5, C6: 1μF / 16V X5R R1: 910kΩ, R1 = (Voltage at IREF - VSS) / IR

TAILOR PIXELS TECHNOLOGY CO., LTD. 2. Absolu te Maxim um Ratin gs ut mu ng Parameter Supply Voltage for Logic Supply Voltage for Display Supply Voltage for DC/DC Operating Temperature Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”. Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Section 3. “Optics & Electrical Characteristics”. If this module is used beyond these conditions, malfunctioning of...

TAILOR PIXELS TECHNOLOGY CO., LTD. 3. Opt ic s & Electr ical Characterist ics ti cs ri ti 3.1 Optics Characteristics Characteristics Brightness (VCC Supplied Externally) Brightness (VCC Generated by Internal DC/DC) Dark Room Contrast Viewing Angle * Optical measurement taken at VDD = 2.8V, VCC = 9V & 7.25V. Software configuration follows Section 4.4 Initialization. 3.2 DC Characteristics Characteristics Supply Voltage for Logic Supply Voltage for Display (Supplied Externally) Supply Voltage for DC/DC Supply Voltage for Display (Generated by Internal DC/DC) Conditions Note 5 (Internal DC/DC Disable)...

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3 AC Characteristics 3.3.1.1 68XX-Series MPU Parallel Interface Timing Characteristics: Symbol tcycle Clock Cycle Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Hold Time Output Disable Time Access Time PWCSL PWCSH Chip Select Low Pulse Width (Read) Chip Select Low Pulse width (Write) Chip Select High Pulse Width (Read) Chip Select High Pulse Width (Write) Rise Time Fall Time

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3.1.2 68XX-Series MPU Parallel Interface w ith Inter nal Char ge Pu mp wi rn rg ump 特别提醒(Special Tips):主板设计务必加电子开关, 否则, 可能引起漏电流现象 (When design main board, Please add Electronic Switch circuit, otherwise, will be caused leak current) 68xx parallel interface Vin R2 D N.C. (GND) C2P C2N C1P C1N VBAT N.C. VSS VDD BS0 BS1 BS2 CS# RES# D/C# R/W# E/RD# D0 D1 D2 D3 D4 D5 D6 D7 IREF VCOMH VCC VLSS N.C. (GND) Recommended Components: C1, C2: 1μF / 16V, X5R C3: 2.2μF C4: 4.7μF / 16V, X7R C5, C6: 1μF R1: 910kΩ, R1 = (Voltage at IREF - VSS) / IREF R2, R3: 47kΩ Q1: FDN338P...

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3.2.1 80XX-Series MPU Parallel Interface Timing Characteristics: Symbol Clock Cycle Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Hold Time Output Disable Time Access Time Read High Time Write High Time Chip Select Setup Time Chip Select Hold Time to Read Signal Chip Select Hold Time Rise Time Fall Time ( Read Timing ) ( Write Timing )