Manufacturer Certificated Product Specification Model: TOX066TSWPG03 0.66″ PM OLED Display Module (64*48) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com [email protected] Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd

TAILOR PIXELS TECHNOLOGY CO., LTD. Revised History Part Number

TAILOR PIXELS TECHNOLOGY CO., LTD. Contents Revision History Contents 1. Basic Specifications 1.1 1.2 1.3 1.4 1.5 Display Specifications Mechanical Specifications Active Area / Memory Mapping & Pixel Construction Mechanical Drawing Pin Definition 2. Absolute Maximum Ratings 3. Optics & Electrical Characteristics 3.1 Optics Characteristics 3.2 DC Characteristics 3.3 AC Characteristics 3.3.1 68XX-Series MPU Parallel Interface Characteristics 3.3.2 80XX-Series MPU Parallel Interface Characteristics 3.3.3 Serial Interface Characteristics (4-wire SPI) 3.3.4 I2C Interface Characteristics 4. Functional...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1. Basic Specifications 1.1 Display Specifications 1) 2) 3) Display Mode: Display Color: Drive Duty: Passive Matrix Monochrome (White) 1/48 Duty Outline Drawing: Number of Pixels: Panel Size: Active Area: Pixel Pitch: Pixel Size: Weight: According to the annexed outline drawing 64  48 18.46  18.1  1.25 (mm) 13.42  10.06 (mm) 0.21  0.21(mm) 0.19  0.19 (mm) TBD 1.3 Active Area / Memory Mapping & Pixel Construction

Remark Original Drawing Contact Side Pixel Detail Scale (10:1) Notes: 1. Color: White 2. Driver IC: SSD1315 3. FPC Number: NFP1315-96 4. Interface: 8-bit 68XX/80XX Parallel, 4-wire SPI, I2 C 5. General Tolerance: ±0.30 Symbol N.C. (GND) C2P C2N C1P C1N VBAT VSS VDD BS1 BS2 CS# RES# D/C# R/W# E/RD# D0 D1 D2 D3 D4 D5 D6 D7 IREF VCOMH VCC VLSS N.C. (GND) Customer Approval Signature Drawing Number TOX066TSWPG03 Unless Otherwise Specified General Roughness Tolerance Dimension ±0.3 Angle ±1 Folding Type OEL Display Module Number: 64 x 48, Monochrome, COG Package TOX066TSWPG03 Soda Lime / Polyimide...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.5 Power Supply for Logic This is a voltage supply pin. It must be connected to external source. Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. Power Supply Driver Current Reference for Brightness Adjustment This pin is segment...

TAILOR PIXELS TECHNOLOGY CO., LTD. 1.5 Pin Definition (Continued) Pin Number Interface (Continued) Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial or I2C mode is selected, this pin must be connected to VSS. Host Data Input/Output...

TAILOR PIXELS TECHNOLOGY CO., LTD. 2. Absolute Maximum Ratings Parameter Supply Voltage for Logic Supply Voltage for Display Supply Voltage for DC/DC Operating Temperature Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”. Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Section 3. “Optics & Electrical Characteristics”. If this module is used beyond these conditions, malfunctioning of the module...

TAILOR PIXELS TECHNOLOGY CO., LTD. 3. Optics & Electrical Characteristics 3.1 Optics Characteristics Characteristics Brightness (VCC Supplied Externally) Brightness (VCC Generated by Internal DC/DC) Dark Room Contrast Viewing Angle * Optical measurement taken at VDD = 2.8V, VCC = 12V & 7.25V. Software configuration follows Section 4.4 Initialization. 3.2 DC Characteristics Characteristics Supply Voltage for Logic Supply Voltage for Display (Supplied Externally) Supply Voltage for DC/DC Supply Voltage for Display (Generated by Internal DC/DC) Conditions Note 5 (Internal DC/DC Disable) Internal...

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3 AC Characteristics 3.3.1.1 68XX-Series MPU Parallel Interface Timing Characteristics: Symbol tcycle Clock Cycle Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Hold Time Output Disable Time Access Time PWCSL PWCSH Chip Select Low Pulse Width (Read) Chip Select Low Pulse width (Write) Chip Select High Pulse Width (Read) Chip Select High Pulse Width (Write) Rise Time Fall Time

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3.1.2 68XX-Series MPU Parallel Interface with Internal Charge Pump 特别提醒(Special Tips):主板设计务必加电子开关, 否则, 可能引起漏电流现象 (When design main board, Please add Electronic Switch circuit, otherwise, will be caused leak current)

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3.2.1 80XX-Series MPU Parallel Interface Timing Characteristics: Symbol Clock Cycle Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Hold Time Output Disable Time Access Time Read High Time Write High Time Chip Select Setup Time Chip Select Hold Time to Read Signal Chip Select Hold Time Rise Time Fall Time ( Read Timing ) ( Write Timing )

TAILOR PIXELS TECHNOLOGY CO., LTD. 3.3.2.2 80XX-Series MPU Parallel Interface with Internal Charge Pump 特别提醒(Special Tips):主板设计务必加电子开关, 否则, 可能引起漏电流现象 (When design main board, Please add Electronic Switch circuit, otherwise, will be caused leak current)