Catalog excerpts
Manufacturer Certificated Product Specification Model: TOJMD096F 0.96″ PM OLED Display Module (128*64) This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd
Open the catalog to page 1TAILORPIXELS TECHNOLOGY CO.,LTD. Revised History Part Number
Open the catalog to page 2TAILORPIXELS TECHNOLOGY CO.,LTD.
Open the catalog to page 3TAILORPIXELS TECHNOLOGY CO.,LTD. 7.2
Open the catalog to page 4TAILORPIXELS TECHNOLOGY CO.,LTD. Display Mode: Display Color: Drive Duty: Passive Matrix Monochrome (White) 1/64 Duty Outline Drawing: According to the annexed outline drawing Number of Pixels: PCB Size: Active Area: Pixel Pitch: Pixel Size: 1.3Active Area / Memory Mapping & Pixel Construction
Open the catalog to page 5NOTES: 1.DISPLAY TYPE: 0.96" OLED 2.VIEWING DIRECTION: All 3.POLARIZER MODE: TRANSMISSIVE/NORMALLY BLACK 4.DRIVER IC: SSD1306 5.Resolution:128x64 6.INTERFACE:SPI/IIC(The default is SPI interface) 7.VOLTAGE:3.3V 7.OPERATING TEMP: -40°C~70°C Customer Approval Signature mm Tolerance Dimension ±0.3 Angle ±1 General Roughness Unless Otherwise Specified TOJMD096F PM OLED Display Module Pixel Number: 128x64, Monochrome By TAILORPIXELS TECHNOLOGY CO.,LTD. Soda Lime / Polyimide Drawing Number Original Drawing TAILORPIXELS TECHNOLOGY CO.,LTD.
Open the catalog to page 6TAILORPIXELS TECHNOLOGY CO.,LTD. Ground of Logic Circuit This is a ground pin. It must be connected to ground Power Supply for OLED This is a voltage supply pin. It must be connected to source The serial clock input SCL The serial data input SDA Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation Data/Command Control This pin is Data/Command control pin. When the pin is pulled high, the input at SDA is treated as display data. When the pin is pulled low, the input...
Open the catalog to page 7TAILORPIXELS TECHNOLOGY CO.,LTD. SPI Switch to IIC : 1. Change R3 to R1. 2. Ground DC pin and CS pin. 3. Use IIC program.
Open the catalog to page 8TAILORPIXELS TECHNOLOGY CO.,LTD. 2. Absolute Maximum Ratings Parameter Supply Voltage for Display Supply Voltage for Logic Operating Temperature Storage Temperature Life Time (80 cd/m ) Life Time (60 cd/m ) Note 1: All the above voltages are on the basis of “GND = 0V”. Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Section 3. “Optics & Electrical Characteristics”. If this module is used beyond these conditions,...
Open the catalog to page 9TAILORPIXELS TECHNOLOGY CO.,LTD. 3.Optics & Electrical Characteristics 3.1Optics Characteristics Characteristics Dark Room Contrast Brightness (VCC Supplied Externally) Brightness (VCC Generated Internal DC/DC) Viewing Angle * Optical measurement taken at VDD = 2.8V, VCC = 7.25V. Software configuration follows Section 4.2 Initialization. Supply Voltage for Logic Supply Voltage for Display (Supplied Externally) Supply Voltage for DC/DC Note 5 (Internal DC/DC Disable) Internal DC/DC Enable Supply Voltage for Display (Generated by Internal DC/DC) Note 6 (Internal DC/DC Enable) High Level Input...
Open the catalog to page 10TAILORPIXELS TECHNOLOGY CO.,LTD. DC/DC) Sleep Mode Current for VDD Sleep Mode Current for VCC Note 5 & 6: Brightness (Lbr) and Supply Voltage for Display (VPP) are subject to the change of the panel characteristics and the customer’s request. Note 7: VDD = 2.8V, VCC = 12V, 100% Display Area Turn on. Note 8: VDD = 2.8V, VCC = 7.25V, 100% Display Area Turn on. * Software configuration follows Section 4.2 Initialization. SPI Interface Timing Characteristics: Symbol tcycle tCSS tCSH tDSW tDHW tCLKL tCLKH tR tF Clock Cycle Time Chip Select Setup Time Chip Select Hold Time Write Data Setup Time...
Open the catalog to page 11TAILORPIXELS TECHNOLOGY CO.,LTD.
Open the catalog to page 12TAILORPIXELS TECHNOLOGY CO.,LTD. D D0 Command Description 1 0 1 Set Contrast Control Double byte command to select 1 out of A1 A0 256 contrast steps. Contrast increases as the value increases. (RESET = 7Fh ) A0h, X[0]=0b: column address 0 is mapped to SEG0 (RESET) A1h, X[0]=1b: column address 127 is mapped to SEG0 C0h, X[3]=0b: normal mode (RESET) Scan from COM0 to COM[N –1] C8h, X[3]=1b: remapped mode. Scan from COM[N-1] to COM0 Where N is the Multiplex ratio. Set VCOMH Deselect Level V COMH deselect level A6h, X[0]=0b: Normal display (RESET) 0 in RAM: OFF in display panel 1 in RAM: ON in...
Open the catalog to page 13TAILORPIXELS TECHNOLOGY CO.,LTD. 4.2VCC Generated by Internal DC/DC Circuit If the noise is accidentally occurred at the displaying window during the operation, please reset the display in order to recover the display function.
Open the catalog to page 14TAILORPIXELS TECHNOLOGY CO.,LTD. Normal Operation Power Stabilized (100ms Delay Recommended) Power down VBAT (50ms Delay Recommended) Normal Operation Power down VBAT Sleep Mode Sleep Mode Power Stabilized (100ms Delay Recommended) Power up VBAT (100ms Delay Recommended) Normal Operation
Open the catalog to page 15TAILORPIXELS TECHNOLOGY CO.,LTD. void OLED_Init(void) { //OLED 复位 OLED_RES_Clr();//RES 置 0 delay_ms(200);//延时 200ms OLED_RES_Set();//RES 置 1 //OLED 初始化 OLED_WR_Byte(0xAE,OLED_CMD);//--turn off oled panel OLED_WR_Byte(0x00,OLED_CMD);//---set low column address OLED_WR_Byte(0x10,OLED_CMD);//---set high column address OLED_WR_Byte(0x40,OLED_CMD);//--set start line address OLED_WR_Byte(0x81,OLED_CMD);//--set contrast control register OLED_WR_Byte(0xCF,OLED_CMD);// Set SEG Output Current Brightness OLED_WR_Byte(0xA1,OLED_CMD);//--Set SEG/Column Mapping 0xa0 左右反置 0xa1 正常...
Open the catalog to page 16TAILORPIXELS TECHNOLOGY CO.,LTD. #define OLED_CMD 0 //write command #define OLED_DATA 1 //write data void OLED_WR_Byte(u8 dat,u8 cmd) { u8 i; if(cmd) OLED_DC_Set(); else OLED_DC_Clr(); OLED_CS_Clr(); for(i=0;i<8;i++) { OLED_SCL_Clr(); if(dat&0x80) OLED_SDA_Set(); else OLED_SDA_Clr(); OLED_SCL_Set(); dat<<=1; } OLED_CS_Set(); OLED_DC_Set(); }
Open the catalog to page 17All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life
11 Pages