Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TBZ050HD-01C TFT Display with Driver Board This module uses ROHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd.
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 2
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 3
TAILOR PIXELS TECHNOLOGY CO., LTD. Feature Size(inch) LCM Resolution supported(Max) Pixel Configuration Interface Touch Panel Optional Key Optional Viewing Direction Brightness (Typ) LCM (W x H xT ) Active Area(W×H) Power connector Audio headset Key connector HDMI connector VGA connector 3. Electrical Characteristics Item Operating Temperature Storage Temperature Supply Voltage
Open the catalog to page 4
TAILOR PIXELS TECHNOLOGY CO., LTD. Signal TMDS Data 2+ TMDS Data2 Sh TMDS Data 2TMDS Data 1+ TMDS Data1 Sh TMDS Data 1TMDS Data 0+ TMDS Data 0 S TMDS Data 0TMDS Clock+ TMDS Clock Sh TMDS ClockCEC NC SCL SDA DDC/CEC GND +5V Hot Plug Detec Description TMDS Transition differential signal 2+ Data2 Shielding ground TMDS Transition differential signal 2TMDS Transition differential signal 1+ Data1 Shielding ground TMDS Transition differential signal 1TMDS Transition differential signal 0+ Data0 Shielding ground TMDS Transition differential signal 0TMDS Transition differential signal Clock+ Clo6ck...
Open the catalog to page 5
TAILOR PIXELS TECHNOLOGY CO., LTD. Function Power ground VSYNC signal HSYNC signal Power ground Red signal + Power ground Green signal + Power ground Blue signal + Power ground I2C data input I2C clock
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 7
TAILOR PIXELS TECHNOLOGY CO., LTD. 7.Optical Characteristics Items Viewing angles Contrast Ratio Response Time White Symbol Condition Min. θT 70 θB 70 Center CR≥10 θL 70 θR 70 CR TON TOFF XW YW XR YR XG YG XB YB U NTSC Luminance Test Conditions: 1. IF= 20mA (one channel), the ambient temperature is 25°C. 2. The test systems refer to Note 1 and Note 2.
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. Note 1: Definition of optical measurement system. The optical characteristics should be measured in the darkroom. After 5 minutes of operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring the center area of the panel. Note 2: Definition of viewing angle range and measurement system. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Note 3: Definition of contrast ratio
Open the catalog to page 9
TAILOR PIXELS TECHNOLOGY CO., LTD. Note 4: Definition of Response time (Test LCD using DMS501): The output signals of photo detector are measured when the input signals are changed from “black” to “white”(rising time) and from “white” to “black”(falling time), respectively. The response time is defined as the time interval between the 10% and 90% of amplitudes.Refer to figure as below. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2)....
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. Test Item High Temperature Storage High Temperature Operation High Temperature/Humidity Operation Test condition 1. After testing, cosmetic and electrical defects should not happen. 2. Total current consumption should not be more than twice of initial value. Temperature Cycle Vibration Test Shock Test after 5 cycle, Restore 2H at 25℃ Power off Not allowed cosmetic and electrical defects. Note: 1. TS is the temperature of panel’s surface. 2. Ta is the ambient temper
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD. 9. Precautions for Use of LCD Modules 9.1 Handling Precautions 9.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 9.1.4 The...
Open the catalog to page 12
TAILOR PIXELS TECHNOLOGY CO., LTD. peeling off this protective film since static electricity may be generated. 9.2 Storage precautions 9.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 9.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : Relatively humidity: 9.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 9.3 The LCD modules should be no falling and violent shocking during...
Open the catalog to page 13All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
