Website:
TAILOR PIXELS TECHNOLOGY CO., LTD.
Catalog excerpts
Manufacturer Certificated Product Specification Model: TOH240XVT-01 2.4″AMOLED Display Module(450*600） This module uses RoHS material Tailor Pixels Technology Co., Ltd. www.tailorpixels.com tailor@tailorpixels.com Ph: 86-755-8821 2653 Contents in this document are subject to change without notice. No part of this document can be reproduced or transmitted by any means for any purpose without the written permission of Tailor Pixels Technology Co., Ltd
Open the catalog to page 1
TAILOR PIXELS TECHNOLOGY CO., LTD. Records of Revision 修改记录 Rev
Open the catalog to page 2
TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 3
loilorpixels TAILOR PIXELS TECHNOLOGY CO., LTD. 1 Module basic Specification 1.1 Module application ♦ This module has a 2.4 inch diagonally measured active area with 450RGBx600 resolutions (600 horizontal by 450 vertical pixel arrays). Each pixel is divided into RED, GREEN, BLUE dots. ♦ This module is display terminals for sports camera and smart home. 1.2 Display Module Specification
Open the catalog to page 4
lailorpixels TAILOR PIXELS TECHNOLOGY CO., LTD.
Open the catalog to page 5
lailorpixels TAILOR PIXELS TECHNOLOGY CO., LTD. asaa km uvr (js mtm m TsaMtf, * ftTaaaa aFPC|g#K - ±fiJ8lt&« a<0.4nmT» ®3*PDL< 0,2rm BonqclinQ BSt
Open the catalog to page 6
TAILOR PIXELS TECHNOLOGY CO., LTD. Test condition: VCC= 3.3V, VDDIO=1.8V , Ta=25°C
Open the catalog to page 7
loilorpixels TAILOR PIXELS TECHNOLOGY CO., LTD. 3.1: Luminance measurement The test condition is at 25°C and measured on the surface of OLED module. • The data are measured after OLEDs are lighted on for more than 5 minutes and displays • equipment CS2000/CS2000A or similar equipments (Field of view:1deg,Distance:50cm) • Measuring surroundings: Dark room. • Adjust operating voltage to get optimum contrast at the center of the display. • Measured value at the center point of panel must be after more than 5 minutes while light up
Open the catalog to page 8
TAILOR PIXELS TECHNOLOGY CO., LTD. The test condition is at 25℃ and measured on the surface of display module Measurement equipment: CS2000/CS2000A or similar equipment. The luminance uniformity is calculated by using following formula. △Bp = Bp (Min.) / Bp (Max.)×100 (%) Bp (Max.) = Maximum brightness in 9 measured spots Bp (Min.) = Minimum brightness in 9 measured spots. 3.3: The definition of Viewing Angle Refer to the graph below marked by θ and Ф 3.4: The definition of Contrast Ratio (Test OLED using CS2000/CS2000A or similar equipments): Contrast Ratio(CR)= Luminance is at “White”...
Open the catalog to page 9
TAILOR PIXELS TECHNOLOGY CO., LTD. 3.5: Definition of Response time. (Test module using DMS 803 or similar equipment): The output signals of photo detector are measured when the input signals are changed from “black” to “white”(Voltage falling time) and from “white” to “black”(Voltage rising time), respectively. The response time is defined as the time interval between the 10% and 80% of amplitudes. Refer to figure as below. Response time of gray to gray: • Measurement equipment: DMS803 or similar equipment. • Test method: we define 8 grays L0-L7, the grays of L0-L7 were defined as:0,36,73,...
Open the catalog to page 10
TAILOR PIXELS TECHNOLOGY CO., LTD. 3.6: Definition of Color of CIE Coordinate and NTSC Ratio. area of RGB triangle 100% area of NTSC triangle 3.7: gamma curve control • • For gamma curve control, request as below: the whole curve’s tolerance must control within +/-0.3, will test the gray scale below: 0~255gray, interval 8 gray ( 0,8,16,24……255) According to below formula chart the curves Measurement equipment: Hunter Lab USPRO, Konica-Minolta CM-3600 Measurement parameter：Refle
Open the catalog to page 11
TAILOR PIXELS TECHNOLOGY CO., LTD. 3.9 Polarization Direction Definition • Viewing direction is normal user viewing direction which is vertical to the display surface • The X axis is defined as parallel line to top&bottom sidelines of the Active Area • PdF which is marked in blue arrow is polarization degree of Front polarizer • The polarization degree parameter must be indicated in range of 0deg to 180deg according to above definition • The angle definition of Polarization: The angle between polarized axis of Polarizer and zero of LCD • Reference: Transmission axis 90deg for normal LCD...
Open the catalog to page 12
loilorpixsls TAILOR PIXELS TECHNOLOGY CO., LTD. AMOLED Interface Definition
Open the catalog to page 13
TAILOR PIXELS TECHNOLOGY CO., LTD. Host Interfac e DC-DC MIPI/SPI/MCU Input Signal MFPC Schematic Diagram WFPC -Tntfrrte*
Open the catalog to page 15
lailorpixels TAILOR PIXELS TECHNOLOGY CO., LTD. Initial setting & sleepout Potter down wwwwvww^ ns«ePcmxiIC ELSSS. ELVSS
Open the catalog to page 16
TAILOR PIXELS TECHNOLOGY CO., LTD. 6.2 Reset Timing Sequence Requirement 6.2.1 Display panel reset timing: 6.3 Communication Interface timing 6.3.1 MIPI-DSI 1 lane Interface Characteristics HS Data Transmission Burst Clock Lane Data Lane
Open the catalog to page 17
TAILOR PIXELS TECHNOLOGY CO., LTD. Preparation tram Low Power Mode to Hvgh Speed Motto I Tvqt t s»^-i ■.» i(» :,<WM.yi| Low Power Mode Diwbte Hi line Terminal i H»jn Spreq Woof. Enable Bn line Twmmation Data Lanes from High Speed Mode to Low Power Mode Timing Data Lanes from Low Power Mode to High Speed Mode Timing Length of any Low Power state Period Time to drive LP-00 to prepare for HS Transmission Time to enable Data lane Receiver line termination measured from when Dn crosses VILMAX Timing Parameters
Open the catalog to page 18
TAILOR PIXELS TECHNOLOGY CO., LTD. Turnaround Procedure TlP-SUREW Bus turnaround (BAT) from MPU to display module timing Tlpx(D) Tlpx(D) T lr<(D) -►"*-► -*- I I I TlP-SUREID) Bus turnaround (BAT) from display module to MPU timing Low Power Mode: NOTE: 1. Tlpx is an internal state machine timing reference. Externally measured values may differ slightly from the specified values due to asymmetrical rise and fall times. 2. Transmitter-specific parameter
Open the catalog to page 19
Turnaround Procedure Bus turnaround (BAT) from MPU to display module timing Bus turnaround (BAT) from display module to MPU timing NOTE: 1. Tlpx is an internal state machine timing reference. Externally measured values may differ slightly from the specified values due to asymmetrical rise and fall times. 2. Transmitter-specific parameter
Open the catalog to page 20All TAILOR PIXELS TECHNOLOGY CO. catalogs and technical brochures
-
TFT LCD serial for Smart Life11 Pages
