TaeguTec Turning Line HUSHi /I /V / / V'/fifKsX / fiJ/V IVibration Free Boring Bar Line with Exchangeable Heads Industry 4.0 Member IMC Group

TaeguTec Turning Line KEY POINT TaeguTec has launched the HUSH-BORE line, a head exchangeable vibration free boring bar line for deep internal turning. Machining depth in internal turning differs according to the shank materials of bars used; steel boring bars are used up to 3XBD (bar diameter) and carbide boring bars up to 5XBD. Deep internal turning, however, is very difficult to machine even with carbide boring bars. With the HUSH-BORE’s damping system, TaeguTec has provided an internal turning solution up to 10XBD. The HUSH-BORE’s damping system located inside the shank is capable of deep...

TaeguTec Turning Line HUSH-BORE shank features ■ Internal vibration damping system - Good surface finish and tool life - Higher depth of cut and feed enables better productivity ■ Serrated coupling design for robust tightening ■ Corrosion resistant stainless steel shanks ■ Available as standard items in 2 different lengths: 7XBD, 10XBD ■ Shanks available as standard items in 7 diameters : 016, 20, 25, 32, 40, 50, 60 mm HUSH-BORE exchangeable head features ■ A variety of head types with various specifications ■ Available inserts - ISO positive inserts: CCMT, DCMT, VBMT - RHINO-TURN negative inserts:...

TaeguTec Turning Line Select inserts that generate low cutting force to minimize vibration  D-Type provides more advantages than the C-Type with reduced rear contact area of the cutting edge.  Stay as close to a 90 degrees entering angle as possible Wiper Insert  Wiper inserts are highly prone to vibration during machining, so it is recommended to use a standard ISO type insert.  TaeguTec recommends using inserts with small corner radii.  Long chips can cause vibrations, so it is recommended to use inserts with good chip control. Maximum shank cutting position Since there is a damping system...

TaeguTec Turning Line Set the shank to the holder so that the head’s upper surface is horizontal to the gauge. TaeguTec recommends the use of slit holders that have the full surface contact of the shank’s cylinder. The mounted shank requires a length of at least 4XBD. It is not recommended to use side lock clamping during operation; this will put the screw in direct contact with the shank

TaeguTec Turning Line QS Anti-vibration shanks for boring OHX

TaeguTec Turning Line QH-HDUNR/L QH-HVUNR/L Hook lever type boring heads ' / Marked: For RHINO-TURN insert Spare parts jjwJP Member IMC Group

TaeguTec Turning Line QH-SCLCR/L Screw type boring heads Spare parts

TaeguTec Turning Line QH-SCLNR/L Screw type boring heads Approach angle jjwJP Member IMC Group

TaeguTec Turning Line QH-SDUCR/L Screw type boring heads Spare parts

TaeguTec Turning Line Screw type boring heads 93° DCONMS DCONMS Approach angle   Marked: For RHINO-M-TURN insert   Marked: For RHINO-TURN insert Spare parts Designation

TaeguTec Turning Line QH-SVUBR/L Screw type boring heads Approach angle Spare parts jjwJP Member IMC Group

TaeguTec Turning Line QH-SWLNR/L Screw type boring heads Approach angle 1* Marked: For RHINO-M-TURN insert Spare parts jjwJP Member IMC Group

TaeguTec Turning Line QH-SXUNR/L Screw type boring heads ■ ❖ Marked: For RHINO-X-TURN insert Spare parts jjwJP Member IMC Group