T-MAG
16Pages

Magnetic Drive pumps are seal-less pumps that use the With over three decades of developing and fine-tuning magnetic technology of a drive magnet and inner magnet connected to drive pumps, T-Mag™ is the answer for reliability and cost- an impeller to move fluid thru the pump. The drive magnet and effective pumping solutions. T-Mag™ has made a name through inner magnet are separated by a rear casing or housing, creating numerous product innovations and patents that allow it to be one a seal-less containment. Magnetic drive pumps prevent the of the mos t reliable magnetic drive pumps on the...

Patented Dry-run Design H i g h E ffi c i e n t F l o w D e s i g n The geometry of the impeller and casing are generated through a hydraulic design program. In addition, Computerized Fluid Dynamics (CFD) reducing hydraulic loss and increasing pump The revolutionized bearing design with dual-channel circulation on both inner and outer surfaces of the bearing contributes to rapid heat dissipation. The circulation leakage of the sealles pump is fully utilized to reinforce convectional heat transfer to thermally balance tr internal temperatures and i prevent damage even under dry running...

Typical Mag Drive Flow Pat h

Temperature Limits: GF-Polypropylene: PVDF: EPDM: Viton: Note: The total length & weight of the pump wil brand of the motor. All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F CFR-ETFE: 0˚F EPDM: -60˚F Viton: -4 0˚F Note: The total length & weight of the pump wil brand of the motor. All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypeopylene: 32˚F CFR-ETFE: 0˚F EPDM: -60˚F Viton: -40˚F Note: The total length & weight of the pump wil brand of the motor. All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

BAR FEET PSIG METERS BAR FEET PSIG METERS Discharge Pressure Motor Power Discharge Pressure Note: The total length & weight of the pump wil brand of the motor. Motor Power Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F Note: The total length & weight of the pump wil brand of the motor. 0 BAR FEET PSIG METERS BAR FEET PSIG METERS BAR FEET PSIG METERS All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F BAR FEET PSIG METERS EFFICIENCY Discharge Pressure BAR FEET PSIG METERS Discharge Pressure Motor Power Note: The total length & weight of the pump wil brand of the motor. BAR FEET PSIG METERS BAR FEET PSIG METERS All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F BAR FEET PSIG METERS 0 BAR FEET PSIG METERS Discharge Pressure Discharge Pressure BAR FEET PSIG METERS EFFICIENCY BAR FEET PSIG METERS Note: The total length & weight of the pump wil brand of the motor. Motor Power All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F Motor Power BAR FEET PSIG METERS BAR FEET PSIG METERS Discharge Pressure Discharge Pressure Note: The total length & weight of the pump wil brand of the motor. Motor Power 0 BAR FEET PSIG METERS BAR FEET PSIG METERS All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Temperature Limits: GF-Polypropylene: 32˚F to 175˚F CFR-ETFE: 0˚F to 212˚F EPDM: -60˚F to 280˚F Viton: -40˚F to 350˚F BAR FEET PSIG METERS BAR FEET PSIG METERS Discharge Pressure Discharge Pressure Note: The total length & weight of the pump wil brand of the motor. Motor Power BAR FEET PSIG METERS BAR FEET PSIG METERS All curves based upon pumping water at sea 68˚F (20˚C). NOTE: Numbers shown to far right of all performance lines denote the diameter of the pump impeller [millimeters (inches)]. Consult factory for availability of impeller t

Your Authorized Distributor: sales@tmagpumps.com 21365 Gateway Court • Brookfield, WI 53045 (855) 848-TMAG (8624) Fax (262) 784-9749 sales@tmagpumps.com www.tmagpumps.com Printed in the U.S.A. Copyright 2017, Anderson Process