Portable Hones
34Pages

Portable Hones HONING UNIT SELECTION GUIDE PEDESTAL MACHINES (ML, EC, MBB, & LBB) PLATED TOOLING (KGM & VSS MACHINES) What will Sunnen Portable Hones do for you? How to select the Power Source for your Sunnen Portable Hone. Sunnen Portable Hones may be driven by a heavy-duty electric drill, air drill, or drill press. Optimum RPM is calculated by dividing 1200 by the bore diameter in inches... for example: 1200 ÷ 6 inches = 200 RPM; or dividing 30,000 by the bore diameter in millimeters... for example 30,000 ÷ 150 millimeters = 200 RPM. If the power source is a drill press or other rigid stroking device, make sure your portable hone is equipped with two universal joints to provide full floating action at the honing head. Remote feed hones should always be used in a rig, either horizontally or vertically. Choose the Proper Portable Hone for Your Application from pages 5.3-5.24. www.sunnen.com CUSTOM ABRASIVES & TOOLING • epair production equipment on the spot R with minimum delay • Repair worn or scuffed air and hydraulic cylinders • Resize bearings • Recondition compressors, engines, pumps • Pull tandem holes into line • Repair hydraulic valves • Remove tool marks from cylinders • Hone I.D.’s for fit during machine assembly • Clean up assembly or heat-treat distortion • Correct I.D. errors in reject parts Sunnen Portable Hones are capable of honing open, shouldered, blind, keyway, splined, tandem, or rifled bores to a uniform surface finish of .08-1.5 micrometer Ra (3-60 microinches Ra) in aluminum, welded, drawn or hardened steel, brass, ceramic, carbide, etc. They can be run in an electric drill, air drill, drill press, or honing rig. PORTABLE, MPS & TUBE HONE ABRASIVES Corrects undersize, taper, out-of-round, barrel or bellmouth shape and misalignment to tolerances of ,013mm (.0005") in diameters from 31,8-914mm (1.250"-36"). Larger sizes up to 1524mm (60") available on special order. Ideal for honing parts too big or awkward to bring to a machine tool. CYLINDER HONING (SV-410 & SV-10 MACHINES Fast and efficient for all kinds of b

For Portable Use of Machine Tooling Universal Joint (Does not come equipped with electrical plug) PORTABLE, MPS & TUBE HONE ABRASIVES CYLINDER HONING (SV-410 & SV-10 MACHINES PLATED TOOLING (KGM & VSS MACHINES) HONING UNIT SELECTION GUIDE For Sunnen Portable Equipment and Cylinder Hones Included with Remote Feed Portahone but must be ordered separately for Hand-Feed Portahones. Universal Joint is required on a hand-held unit to provide full floating action in a setup where the part and power source are rigidly mounted. Order as follows: AN-70 Universal Joint for Remote Feed Portahones with...

SNJ-10 Portable Hone shown assembled with Stone Set and AN-26A Drive Shank. Will hone bores up to 457 mm (18") long as shown; order additional Shaft Extensions for longer bores Requires 13 mm (1/2") chuck capacity. Accessories AN-70 Universal Joint AN-80 Quick Coupler See page 5.2 In some cases, stones other than the RECOMMENDED STONES may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or finer. As a general rule, hard materials require soft stones; soft materials require hard stones; rough holes...

SN-75 Portable Hone Hand Feed HONING UNIT SELECTION GUIDE I.D. Range: 44 mm – 51 mm 1.750" – 2" SN-75 Portable Hone shown assembled with Stone Set, Drive Shank, and 305 mm (12") Shaft Extension. 102 mm (4") stone length. Will hone bores up to 533 mm (21") long as shown; order additional Shaft Extensions for longer bores. Requires 13 mm (1/2") chuck capacity. Drive Shanks Part Number Specify SN-75 Basic Hone, (includes 76 mm (3") Drive Shank, 305mm (12") Extension one Universal Joint and Honehead. See page 5.8 for repair parts.). Shaft Extensions CUSTOM ABRASIVES & TOOLING PORTABLE, MPS &...

Accessories AN-70 Universal Joint when using the SN-75 in a drill press or other rigid stroking device. Use in place of Drive Shank AN-26A AN-80 Quick Coupler In some cases, stones other than the RECOMMENDED STONES above may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or finer. If the stone wears out too fast, use a harder stone; if it does not cut, use a softer stone. Contact Customer Service for price and availability. r { * 1st choice ** 2nd choice. Use if A45 does not cut. *** 3rd choice....

JN-95 Portable Hone shown assembled with Stone Set, Drive Shank, and 305 mm (12") Shaft Extension. 102 mm (4") stone length. Will hone bores up to 533 mm (21") long as shown; order additional Shaft Extensions for longer bores. Requires 13mm (1/2") chuck capacity. Specify JN-95 Basic Hone (includes 76 mm (3") Drive Shank, 305 mm (12") Extension, one Universal Joint and Hone Head). See page 5.8 for repair parts. Additional Shaft Extensions may be ordered from table below to make up any practical length. Drive Shank can be used with any combination of Extensions. See Stone Sets Table on Page...

Available Stones Grit Size NOTE: For extremely rough bores T20-XM51-X735 36 grit resin-bond aluminum oxide stone sets are available. PHT Plateau Honing Tools Accessories AN-70 Universal Joint AN-80 Quick Coupler AN-79A Replacement Recommended Stones Sets Stone Sets*(2 Stones and 2 Guides) For General Purpose Honing 51-56mm 56-61mm 61-66mm Provides instant coupling or uncoupling of hone from drive motor. Install between Drive Shank and Shaft Extension, or between Drive Shank and Hone Head on short bores. In some cases, stones other than those recommended above may hone faster or last longer....

Portable Hones & Repair Parts JN-95 Portable Hone Hone Body Universal Joint Complete Adjusting Nut and Washer Hone Body Universal Joint Complete Adjusting Nut and Washer PORTABLE, MPS & TUBE HONE ABRASIVES CYLINDER HONING (SV-410 & SV-10 MACHINES PLATED TOOLING (KGM & VSS MACHINES) HONING UNIT SELECTION GUIDE Hone Body Body Gear Universal Joint Complete Center Pinion Adjustment CUSTOM ABRASIVES & TOOLING Hone Body Body Gear Set Universal Joint Complete Center Pinion Adjustment