For Diameter Range inches Hard Blocks Standard Type Blocks Alum. Cylinders (Special Finish Stones) Hard Blocks Base Finishing before Plateau Honing Standard Type Blocks Alum. Cylinders (Special Finish Stones) Base Finishing before Plateau Honing Hard Blocks Standard Type Blocks Cylinders with Ports Hard Blocks and Sleeves Standard Type Blocks Cylinders with Ports Special Applications Base Finishing before Plateau Honing VW, Mercedes, High Nickel Race Blocks Air Cooled Cylinders Special Applications Standard Type Blocks Aircraft Type Cylinders Aircraft Type (Hard Tip) Air Cooled Cylinders Hard Blocks and Sleeves Hard Blocks and Sleeves Base Finishing before Plateau Honing Standard Type Blocks Aluminum Blocks, Alum. Cylinders High Nickel Race Blocks, Alum. Cylinders Alum. Cylinders (Special Finish Stones) High Nickel Race Blocks, Alum. Cylinders Alum. Cylinders (Special Finish Stones) Polishing, Plateau Honing Aircraft Type Cylinders Air Cooled Cylinders Hard Blocks and Sleeves Hard Blocks and Sleeves Base Finishing before Plateau Honing Standard Type Blocks Aluminum Blocks, Alum. Cylinders High Nickel Race Blocks, Alum. Cylinders Alum. Cylinders (Special Finish Stones) High Nickel Race Blocks, Alum. Cylinders Alum. Cylinders (Special Finish Stones) Polishing, Plateau Honing Hard Cylinders with Ports Hard Cylinders Cylinders with Ports Base Finishing before Plateau Honing Standard Type Blocks Cylinders with Ports Base Finishing before Plateau Honing Standard Type Blocks Hard Cylinders with Ports Hard Cylinders *For special honing applications, contact the Sunnen Customer Service Department. Large Hone Head 1 set per box Standard Hone Head 6 sets per box Block Reconditioning Junior Hone Head 6 sets per box Stone Length Order These Stone Sets Used with Master Holder Set Midget Hone Head 6 sets per box Cylinder Head Honing Stone Sets for Use With SV-10/SV-20/CV/CK

SV-10/SV-20/CV/CK Accessories & Supplies Cylinder Head Stone Sets for High Performance Engines Honed on Sunnen CV-616 and CK-10 Connecting Rod Block Reconditioning These Stone Sets are available for producing specific finishes for high performance engines. Contact Customer Service, Sunnen Products Co. for full details. As a general rule, however, on standard cast iron blocks the following surface finish will be produced: Stone Set Approx. Surface Finish Microinches Ra Micrometers Ra Chamfers the sharp edges of cylinders for safe piston and ring installation. Handles all diameter cylinders or...

SV-20/SV-400 Vertical Honing Machine Accessories and Supplies NOTE FOR ALL HONE HEADS: Universal joint area must be packed with mobil grease #28 before boot is in place. Sunnen Part #SML-100. Retaining Spring For Stones Stoneholder: .447" (11,3 mm) High Range: 3.41"-3.69" (87 - 94 mm) Stoneholder: .582" (15 mm) High Range: 3.68"-3.96" (93 - 101 mm) Stoneholder: .717" (18 mm) Range: 3.95"-4.23" (100 - 107 mm) Stoneholder: .852" (21,6 mm) High Range: 4.22"-4.44" (107 - 113 mm) Stoneholder Clamp Plate Screw Ref: 5.0 x 8 x 16 mm SHCS Expansion Screw Thrust Washer Thrust Bearing Spacer Shear Pin Ref:...

SV-400/SV-10/SV-20/CK-21 Vertical Honing Machines Accessories and Supplies GHSS-1950 Hone Head GHSS-1480 Hone Head Cylinder Head Retaining O Rings For Stones Expansion Screw Thrust Washer Universal Joint & Rod Driveshaft Truing Grit (70 Grit) Spring Tool Retaining O Rings For Stones Expansion Screw Thrust Bearing Thrust Washer Universal Joint & Rod Driveshaft Truing Grit (70 Grit) Accessories and Supplies Hone Part Number Block Reconditioning Resurfacing Holder Set Part Number N/A N/A N/A N/A N/A N/A Number Per Set Stone Sets (__)=Abrasive Spec Note: ach hone head purchase includes all master...