Catalogs >
Sunnen Products Company >
43-45.pdf: Type CR Honing Units

43-45.pdf: Type CR Honing Units
3Pages

Catalog excerpts

Type CR Honing Units For Rod Reconditioning (Journal End) Range: 1.450"-4.700" (36,8-119,4 mm) These honing units will produce a round and straight rod bore and allow you to recondition the rod to original factory size, assuring a perfect fit of inserts. They are specially designed to remove stock from the reduced bore without enlarging the diameter across the parting line. After cap and rod faces have been ground at right angles to the side of the rod to reduce the diameter of the bore, these honing units are used to bring the bore back to standard size. For Complete Honing Unit Order Honing Units Replacement Parts Shoe (2 per Pkg.) Wedge Plate Part No. Large Small Range inches Order LBN-62 Honing Unit Set for complete coverage of most popular cars and trucks. Covers diameters from 1.600" to 2.700" (36,8 to 68,6 mm). OR Order individual honing units as needed. Each unit is complete with wedge, wedge plates and shoes. Select From Chart Below Replacement Parts CR Stones for CR-1450 Thru CR-1750 Mandrels CR-2 Medium Finishing CR-4 Fine Finishing Y44-J65 Aluminum Rods CR Stones for CR-1900 Thru CR-4500 Mandrels CR-9 Aluminum Rods/Titanium CR-10 For Rough Honing, Manual Stroking CR-10N For Rough Honing, Power Stroking CR-12 For Medium Finish Honing, Manual Stroking CR-12-8 For Medium Finish Honing, Power Stroking CR-14 For Fine Finish Honing, Manual Stroking Tension Block LN-1685A—For CR-1450 thru CR-1750. LN-1337A—For CR-1900 and up. Shoe Clamps (Includes 4 clamps and screws.) LN-1637A—For CR-1450 thru CR-1750. CR-45A—For CR-1900 and up. Includes CR-44A (pkg. 4 screws). Bronze Shoes For Power and Long Life (Manually Stroked Rod Reconditioning). For CR-1450 thru CR-1750 Mandrels—order P/N PD-B. For CR-1900 thru CR-4500 Mandrels—order P/N CR-50B. Stone Selection Chart

Open the catalog to page 1

All-Steel and Lifetime Honing Units For Connecting Rods (Pin Fitting) Range: .744"-2.625" (18,9-66,7 mm) For Con-Rod Bushings and Press-Fit Type Rods All-steel and Lifetime mandrels, specially made for fitting pins in conrods. Stone and shoe are of proper length to produce straight, round, accurate holes. The all-steel mandrels do not have replaceable shoes. Order in Convenient Sets. For Complete Honing Unit Order Replacement Parts Replacement Wedge (Should be replaced when it begins to show wear.) LN-3688A Replacement Stone Retainer LN-3218A Replacement Wedge Guide Part No. Stones KL-5...

Open the catalog to page 2

Lifetime Honing Units For Connecting Rods (Pin Fitting) Range: .990"-2.625" (25,1-66,7 mm) For: • Pin fitting in con-rods over 1.000" (25,4 mm) • Small cylinders in motorcycles, lawn mowers, outboard motors, etc. Mandrel does not wear…shoes are replaceable. Notes: 1. Length of Honing Stone Surface—3-9/32" (81,7 mm). 2. Allow for extra stock in new bushings to be sure honing unit will enter the hole. For Complete Honing Unit Order Honing Units Med. Fine Rough Finish Finish Replacement Parts (Included with Mandrel) Truing Sleeve Mandrel (Includes Wedge and Shoes) Shoe (2 per Steel Applica-...

Open the catalog to page 3