PUMP SLPD 20/20-64/32 DIN SAVTEC SLPD 20/20-64/32 DIN Savtec is equipped with a SAVTEC shut-off valve. Using a Savtec valve makes it possible to control the SLPD pump so it only feeds oil when required. SLPD 20/20-64/32 DIN Savtec´s valve is available for electrical 24 V or pneumatic remote control. The signal is obtained from a panel switch or automatically from, e.g. the parking brake, pressure sensor or diode gate. With a closed Savtec valve it generates neither flow nor pressure, and in doing so does not load the power take-off. This has a positive effect on fuel economy. SLPD 20/20-64/32 DIN Savtec features extra lubrication ducts on the bearings for lubrication even when the pump is run with the Savtec-valve closed. The pump comes in eight different sizes, where three models feature differentiated flows. Pumps with differentiated flow increase the field of application as they can provide three different flows: one small, one large and one combined flow. Max pressure is 330-350 bar depending on the model. Other advantages: • Independent direction of rotation • A cost effective total solution in relation to a conventional installation using two pumps in a splitter gear box • Extremely low noise level • Smooth operation over the entire speed range • Long life due to high demands on material selection, such as bearings, seals, etc. • O-rings on all contact surfaces as well as double shaft seals eliminate oil leakage from the pump and power take-off • The Savtec valve can also be used as an emergency stop GB - Printed: 04/02/2014 06:03:26 - Page 1/5 Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com

Pump SLPD 20/20-64/32 DIN SAVTEC VERSIONS, MAIN DATA Example SL Line Sunfab In-Line Dual flow pump 7. Connection cover S4 Sunfab standard SLPD Sunfab standard Savtec valve is ordered seperately. Indicate when ordering - Electric or Pneumatic - Suction connection 50 or 64 mm. GB - Printed: 04/02/2014 06:03:26 - Page 2/5 Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com

Pump SLPD 20/20-64/32 DIN SAVTEC Pump SLPD 20/20-64/32 DIN SAVTEC 20/20 Theoretical oil flow at pump speed Max working pressure Weight Dimensions Min. dimensions Tare-weight torque GB - Printed: 04/02/2014 06:03:26 - Page 3/5 Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com

Pump SLPD 20/20-64/32 DIN SAVTEC GB - Printed: 04/02/2014 06:03:26 - Page 4/5 Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com

Pump SLPD 20/20-64/32 DIN SAVTEC WARNING When the pump is running: 1. Do not touch the pressure hose 2. Watch out for rotating parts 3. The pump and hoses may be hot Sunfab reserves the right to make changes in design and dimensions without notice. Printing and typesetting errors reserved. GB - Printed: 04/02/2014 06:03:26 - Page 5/5 Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com