Catalog excerpts
047 056 064 084 090 47.1 56.0 63.5 83.6 90.7 40 40 40 40 40 35 35 35 35 35 63 00 6300 6300 5200 5200 5 700 5700 5700 4700 4700 3 00 300 300 300 300 1 45 175 195 215 230 65 80 90 100 110 7 .5 8.9 10.0 13.3 14.4 2.6 2.6 2.6 7.4 7.4 1 8.3 18.3 18.3 26.0 26.0 Displacement cm3rev. Working pressure max. intermittent MPa max. continuous MPa Revolutions max. intermittent rpm max. continuous rpm min. continuous rpm Power max. intermittent kW max. continuous kW Start torque theoretical value NmMPa Mass moment of inertia ( x 10 -3) kg m2 Weight kg Type Data concerning RPM are based on maximum premitted peripheral velocity for the tapered roller bearings. Sunfab SCM M2 is a range of robust axial piston motors especially suitable for winch-, slewing-, wheel- and track drives. Sunfab SCM M2 is of the bent-axis type with spherical pistons. The design results in a compact motor with few moving parts, high starting torque and high reliability. Motor SCM 047–090 M2 GB The SCM M2 covers the entire displacement range 47–90.0. cm3/rev at a maximum working pressure of 40 ...MPa.. Sunfab SCM M2’s well dimensioned, double tapered roller bearings permit high shaft loads and lead to excellent speed characteristics. Intermittent power data are based on maximum continuous speed and maximum working pressure. Continuous power data are based on maximum output power without external cooling of the motor housing. Intermittent duty is defined as follows: max 6 seconds per minute, e g peak RPM when unloading or accelerating. Sunfab SCM M2’s high level of reliability is based on the choice of materials, hardening methods, surface structures and the quality assured manufacturing process.
Open the catalog to page 1Temperatures/Housing cooling Excessive system temperature reduces the life of the shaft seal and can lower the oil viscosity below the recommended level. A system temperature of 60 °C and a drain flow temperature of 90 °C must not be exceeded. Cooling/flushing of the motor housing can be needed to keep the drain flow temperature at an acceptable level. Suggested flow: Motor SCM Flushing l/min Cont. RPM 047-064 4-10 2500 084-090 6-12 2200 Hydraulic fluids High performance oils meeting ISO specifications – such as HM, DIN 51524-2HLP, or better – must be used. A min. viscosity of 10 cSt is...
Open the catalog to page 5WARNING When the motor is in use: 1. Do not touch the pressure pipe 2. Beware of rotating parts 3. The motor and pipes can reach high temperatures 3203GB0705 Produced in Sweden by Bohman Information AB / Gävle Offset Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Phone: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.se
Open the catalog to page 6All Sunfab Hydraulics catalogs and technical brochures
-
ANTI-CAVITATION VALVE
2 Pages
-
ANTI-CAVITATION VALVE
2 Pages
-
Flushing Valve
2 Pages
-
Speed Sensor
4 Pages
-
DIODE GATE
2 Pages
-
INJECTOR
2 Pages
-
SAM 010-130 DIN
7 Pages
-
SVH 130
20 Pages
-
SCM 012-130 DIN
7 Pages
-
SCM 010-130 SAE
12 Pages
-
SCM 010-130 ISO
12 Pages
-
SAP 084, 108 DIN Optimised
4 Pages
-
SAPT 090, 130 DIN
4 Pages
-
SAP 012-108 DIN
4 Pages
-
SCPD 76/76 DIN
4 Pages
-
SLPD 40/20-64/32 SAE
4 Pages
-
SLPD 20/20-64/32 DIN SAVTEC
5 Pages
-
SLPD 20/20-64/32 DIN
4 Pages
-
SCPD 56/26 DIN By-Pass
4 Pages
-
SCPD 56/26 DIN
4 Pages
-
SCM 025-108 M2
8 Pages
-
SCM 012-130 SAE
12 Pages
-
SCPT 090, 130 DIN
4 Pages
-
SCP 012-130 ISO
7 Pages
-
SCP 084, 108 DIN Optimised
4 Pages
-
SAP 040-064 DIN
4 Pages
-
SCP 012-108 DIN
4 Pages
-
Product Catalogue
25 Pages
-
Accessories Catalog
28 Pages
-
axial piston hydraulic motor SAE
11 Pages
-
Anti-Cavitation Valve
2 Pages
-
Splitter gearbox SZ 121
2 Pages
-
SVH 062, 092, 112
16 Pages
-
SC 5012-5108 SAE
2 Pages
-
SC 012-108 DIN
2 Pages
-
suction oil filter
2 Pages
-
hydraulic relief valve
2 Pages
-
oil tank
2 Pages
-
power take-off for engine
2 Pages
-
dual shaft gearbox
2 Pages
-
variable flow hydraulic pump
16 Pages
-
hydraulic truck pump
2 Pages
Archived catalogs
-
axial piston hydraulic motor
10 Pages