H Customer Unit Size 3 - Africa / Middle East Output Bore 307 Input Shaft Position 000 - see table for Taper-Grip® Bush code Special Order (For Internal Use Only) Output Bearing D - Deep Groove T - Taper Roller 1 Issue 1 - Metric 0 - Inch Bore Type 012 - Metric 113 - Inch Size Code Taper HSM Grip Size B C D E F G H J S K K L M Shaft Combination M - Metric Input, Metric Output A - AGMA Input, AGMA Output B - Metric Input, BS Output 7/16” 15/16” 3/16” 7/16” 15/16” 7/16” 15/16” 7/16” C - Hyd Input, Metric Output D - Hyd Input, AGMA Output E - Metric Input, Taper Grip Output F - AGMA Input, Taper...

Key indicates that power is constrained by thermal limitations. Please consult for effect on using cooling fans.

HH Holes JJ dia x KK full thread

See bore size table. See page 22 & 23 See input shaft table. See page 25. Weight single

HH Holes JJ Dia x KK full thread HH Holes JJ dia x KK full thread both sides

Weight Single (kg) Double

Hub Code Deep Groove Unit Size Inch Bore Sizes Available Taper Roller

Standard Inch Bores Shaft Diameter (inch)

Metric reducing bushes Unit Size Standard bore Unit Size Standard bore Reducing bush bores Standard bore Reducing bush bores Standard bore Reducing bush bores Inch reducing bushes (BS46 keyways only) Reducing bush bores Standard bore Reducing bush bores Standard bore Reducing bush bores

Unit Size Unit Size Shaft Diameter D (inch) Unit Size Unit Size Shaft Diameter D (inch)

Unit Size

Unit Size Unit Size

Keep as close as possible to reducer to reducer

Screw Conveyor

Keep close This angle should be a right angle but may vary up to o a maximum of 15 either way Torque arm and belt take up Keep close Belt drive may be located to the right if desired. Torque arm may be mounted to the right if desired

Screw size Qty. & Code Thrust Collar Screw Torque (max) Code Nm Ib ft Thrust Collar Taper-Grip® bushing

Unit Size Approximate Capacity - Litres 13:1, 20:1 & 25:1 Mounting Position

Part Ident Description Case IPS Case BSS Hollow dowel Case bolt Case nut Case plain washer Case lockwasher Input shaft metric & pinion (5:1) AGMA Input shaft metric & pinion (13:1) AGMA Input shaft metric & pinion (20:1) AGMA Input shaft metric & pinion (25:1) AGMA Input shaft oilseal Input shaft bearing Input shaft retaining ring (20:1) (25:1) Backstop cover Backstop cover screw Backstop cover lockwasher 1st. Reduction gear (13:1) 1st. Reduction gear (20:1) 1st. Reduction gear (25:1) 1st. Reduction gear key Intermediate pinion Intermediate bearing Intermediate cover 2nd. Reduction gear 2nd Reduction...

Part Ident Case IPS Case BSS Hollow dowel Case bolt Case nut 6 Case plain washer Case 7 lockwasher Input shaftmetric & pinion (5:1)AGMA Input shaftmetric 8 & pinion (13:1)AGMA Input shaftmetric & pinion (20:1)AGMA Input shaftmetric & pinion (25:1)AGMA 9 Input shaft oilseal 10 Input shaft bearing 11 Input shaft retaining ring (20:1) (25:1) 12 Backstop cover 13 14 Backstop cover screw Backstop cover lockwasher 1st. Reduction gear (13:1) 1st. Reduction gear (20:1) 1st. Reduction gear (25:1) 1st. Reduction gear key Intermediate pinion Intermediate bearing Intermediate cover 2nd. Reduction gear 2nd....

Part Ident Case Right Hand 1 Case Left Hand 1 Hollow Dowel 2 Case Bolt See (1) Case Nut See (1) Case Plain Washer 4 Case Lockwasher See (1) Input Shaft & Pinion (13:1) 1 Input Shaft Oil Seal 1 Input Shaft Bearing 2 Backstop Cover 1 Backstop Cover Gasket 1 Backstop Cover Screw 6 Backstop Cover Lockwasher 6 Torque Arm Case Bolt 2 Torque Arm Case Bolt Nut 2 Torque Arm Case Bolt Lockwasher 2 1st Reduction Gear (13:1) 1 1st Reduction Gear (20:1) 1 1st Reduction Gear Key 3 Intermediate Pinion (13:1, 20:1) 1 Intermediate Pinion Distance Piece 1 Intermediate Bearing 2 Intermediate Cover 2 2nd Reduction...

Part Ident Extension Locknut 1 Turnbuckle 1 Fulcrum 1 Fulcrum Bolt 1 Fulcrum Bolt Nut 1 Fulcrum Lockwasher 1 Input Shaft Cover 1 Input & Intermediate Cover Screw 18 Input & Intermediate Cover Screw Lockwasher 18 Input & Inter. Cover Shim (0.50mm) AR Input & Inter. Cover Shim (0.25mm) AR Input & Inter. Cover Shim (0.15mm) AR Input & Inter. Cover Shim (0.07mm) AR Input & Inter. Cover Shim (0.05mm) AR Output Cover 2 Output Cover Screw (see 2) Output Cover Lockwasher (see 2) Output Cover Shim (0.5mm) AR Output Cover Shim (0.25mm) AR Output Cover Shim (0.15mm) AR Output Cover Shim (0.07mm) AR Output...

Unit Assembly size

Sumitomo (SHI) Cyclo Drive Germany GmbH