Group: Sumitomo
Catalog excerpts
HYDRAULIC CRAWLER CRANE Lifting Capacities HITACHI SUMITOMO
Open the catalog to page 1Variation of The Attachment Line Speed * Front / Rear Winch Boom Hoist Winch Swing Speed Travel Speed * Gradeability Engine Model Engine Rated Output Power Note : Speeds marked with "*" may vary depending on load applied. Crane Specification (Boom Longest Length) Boom Length Ground Contact Pressure Overall Operating Weight 12 to 54 79.4 (0.81) (Boom longest length with 15 t hook) Approximately 68.2 (Boom longest length with 15 t hook)
Open the catalog to page 2Crane Specification (Boom Longest Length with Aux. Sheave) Boom Length Ground Contact Pressure Overall Operating Weight Crane Specification (Boom Longest Length with Crane Jib) 12 to 51 80.3 (0.82) (Boom longest length + aux. sheave, 15 t + 6.5 t hook attached) Approximately 68.9 (Boom longest length + aux. sheave, 15 t + 6.5 t hook attached) Boom Length Crane Jib Length Boom + Crane Jib Longest Length Ground Contact Pressure Overall Operating Weight 81.3 (0.83) (Boom + crane jib longest length, 15 t + 6.5 t hook attached) Approximately 69.8 (Boom + crane jib longest length, 15 t + 6.5 t...
Open the catalog to page 3VARIATION Variation of The Attachment SPECIFICATIONS Specifications Crane Specifications Clamshell Specifications
Open the catalog to page 4TECHNICAL DATA Weights and Dimensions of Disassembled Units Equipment List
Open the catalog to page 5Specifications Engine Model Type Displacement Rated Output Fuel Tank Capacity Notes Swing System ISUZU 6HK1 4-cycle, Water-cooled, Direct injection, Turbo-charged, Diesel engine 7.79 liters 140 kW / 2,000 min-1 (190 ps / 2,000 rpm) 285 liters Engine meets Tier 2 / Stage II of engine exhaust gas emission regulations in USA, Europe, and Japan. Engine rated horsepower is based on international rating formula that includes engine alternator and without fan. Constructed with a hydraulic motor with reduction gear and multi-disc brakes and a swing bearing which has inner tooth. Counterweight Upper...
Open the catalog to page 6Crane Specifications Dimensions and Specifications Crane Specifications Crane Specifications Hook Weight Max. Lifting Load × Working Radius Basic Boom Length Max. Boom Length Max. Crane Jib Length Max. Boom + Jib Length Ground Contact Pressure Overall Operating Weight 70 × 3.7 12 54 9 to 18 45 + 18 75.5 (0.77) (w / Basic Boom, 70 t Hook) Approximately 64.8 (w / Basic Boom, 70 t Hook) NOTE : Data is expressed in SI units followed by conventional units in ( ). Front / Rear Winch Rope No. of Falls and Lifting Load Hook Capacity ( t ) 70 40 15 6.5 Maximum Rated Load ( t ) 6 Falls 5 Falls 39...
Open the catalog to page 7Crane Specifications Boom and Crane Jib Configurations Boom and Crane Jib Configurations Boom Configurations Aux. Sheave Installable Boom Length Boom Length (m) With Aux. Sheave Check the pendant rope with referring to the imprints on the rope end. Dimensions Not Shown In The Figure Pendant Rope
Open the catalog to page 8Crane Specifications Combination of Boom and Crane Jib (Offset Angle 10° and 30°) Combination of Boom and Crane Jib (Offset Angle 10° and 30°) Combination of Boom and Crane Jib (Offset Angle 10° and 30°) Boom Length (m) Crane Jib (Offset Angle 10° and 30°) Crane Jib Length (m) Offset Angle Check the pendant rope with referring to the imprints on the rope end. Dimensions Not Shown In The Figure
Open the catalog to page 9Crane Specifications Working Ranges Working Ranges Main Boom Maximum Boom Angle Height Above Ground (m) 10 Minimum Boom Angle
Open the catalog to page 10Crane Specifications Working Ranges Maximum Boom Angle 35 Height Above Ground (m) Minimum Boom Angle
Open the catalog to page 11Crane Specifications Working Ranges Maximum Boom Angle 9 m Crane Jib Offset Angle 10° 9 m Crane Jib Offset Angle 30° 65 60 55 50 Height Above Ground (m)
Open the catalog to page 12Crane Specifications Working Ranges Maximum Boom Angle 13.5 m Crane Jib Offset Angle 10° 13.5 m Crane Jib Offset Angle 30° 50 Height Above Ground (m)
Open the catalog to page 13Crane Specifications Working Ranges Maximum Boom Angle 18 m Crane Jib Offset Angle 10° 18 m Crane Jib Offset Angle 30° 50 Height Above Ground (m)
Open the catalog to page 14Crane Specifications Gross Rated Load Table Gross Rated Load Table Main Boom Notes: 1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions. 2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by...
Open the catalog to page 15Crane Specifications Gross Rated Load Table Notes: 1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions. 2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by Ministry of Health, Labour and Welfare,...
Open the catalog to page 16Crane Specifications Gross Rated Load Table Main Boom with Aux. Sheave Unit: ton Working Radius(m) 8.0 9.0 Notes: 1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions. 2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and...
Open the catalog to page 17Crane Specifications Gross Rated Load Table Notes: 1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions. 2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by Ministry of Health, Labour and Welfare,...
Open the catalog to page 18All Sumitomo Heavy Industries Construction Crane catalogs and technical brochures
-
SCX800-2
6 Pages
-
SCX400
2 Pages
-
SCX550
2 Pages
-
6000 SLX
6 Pages
-
UCX350
4 Pages
-
line-up catalog
4 Pages
-
SCX1200-3
8 Pages
-
SCX1000A-3
8 Pages
-
SCX700E pages 1/2
2 Pages
-
SCX550E
2 Pages