*mydirectindustry

ReNEW NA Series

Product catalog summary

Overview: The ReNEW NA Series is a line of wastewater reuse reverse osmosis machines designed for low-flux applications, particularly after membrane bioreactor (MBR) or tertiary ultrafiltration (UF) treatment. These machines are suitable for polishing effluents from GE's Z-MOD, Z-BOX, and Z-PAK Series MBR and UF packaged plants.

Key Features:

Separated control and high voltage enclosures with a single power disconnect.
Allen Bradley CompactLogix PLC and PanelView+700 Touch Screen for control and monitoring.
Instrumentation includes flow meters, conductivity, pH, pressure, and ORP sensors.
Options for GE Fanuc PLC, Ethernet communication, and advanced cleaning systems.

Feed Water Guidelines:

BOD < 20 ppm; TOC < 5 ppm.
Phosphate levels require simulation for scaling and antiscalant dosing.
NTU < 1; SDI < 5; TDS design 2,000 ppm.

Operating Parameters:

Design recovery rate of 75% with a temperature range of 36-87 ºF.
System inlet pressure between 30-60 psi and back pressure < 15 psi.

Materials of Construction:

High-pressure piping made of 316 Stainless Steel; low-pressure piping of PVC.
Frame constructed from painted blue carbon steel with Nema 4 enclosures.

Membrane Elements and Housings:

Membrane model AG-400LF with a rejection rate of 98.0-99.0%.
Housing material is FRP with a pressure rating of 450 PSI.

GE ReNEW Models: The series includes models with varying permeate, concentrate, and feed rates, ranging from 55 gpm to 440 gpm.

Pumps and Motors: Each model is equipped with GE Tonkaflo pumps, with motor power ranging from 25 HP to 75 HP, depending on the model.

Installation and Utility Requirements:

Inlet and outlet flange sizes vary by model, with a minimum inlet water pressure of 30 psi.
Power requirements are 480 VAC, 3-phase, 60Hz.

Skid Dimensions and Weight: Dimensions and shipping weight vary by model, with the largest model weighing approximately 16,000 lb.

Catalog excerpts

Fact Sheet ReNEW NA Series Wastewater Reuse Reverse Osmosis Machines 50 to 330 gpm Separated Control & High Voltage Enclosures with single power disconnect Allen Bradley CompactLogix PLC Communication RS485 HMI Allen Bradley PanelView+700 Touch Screen 4-20 mA Instruments on Touch Screens Primary and Final Pressure Transmitters Motor Starter: VFD (mounted on frame) Bank-by-bank cleaning manifolds and valves RO permeate Flush on Shutdown Options Available GE Fanuc PLC Ethernet Communication CIP PRE with heater for advanced membranes cleaning DuraSlick* membrane elements for higher fouling applications (with flow & recovery decrease and pump change) Feed water Guidelines BOD < 20 ppm; TOC < 5 ppm COD - must define what is creating COD Phosphate – Use Argo Analyzer to simulate scaling and calculate antiscalant dose NTU < 1; SDI < 5 TDS design 2,000 ppm. Higher levels require pump size review Recovery Rate can vary +/- 5% Find a contact near you by visiting www.gewater.com and clicking on “Contact Us”. * Trademark of General Electric Company; may be registered in one or more countries. ©2013, General Electric Company. All rights reserved. AM-FSroReNEWNA_EN.doc Jun-13

Open the catalog to page 1

Membrane Elements and Housings Cartridge Filtration Housing model………………………..GE HX-0740-3.0-V316 Housing material………………………… 316 Stainless Steel Cartridge filter……..….1-micron nominal, ROsave.Z*s GE ReNEW Models MODEL Concentrate Rate: Feed Rate: Pumps and Motors Model: Manufacturer: Quantity: Motor Power and type: Installed Power: Design Flow Rate: Design boost pressure: Membrane Elements and Housings Membranes Quantity: Memb. Housing Style: 18 6 element long, 4 port 36 6 element long, 4 port Banking Arrangement: 54 6 element long, 4 port 72 6 element long, 4 port 90 6 element long, 4 port 108...

Open the catalog to page 2

ReNEW NA Series

ReNEW NA Series

Catalog excerpts

All Suez Water Technology & Solutions catalogs and technical brochures

Archived catalogs