Pedestrian Electric Hydraulic Stacker with Manual Drum Rotation Bespoke Handling Equipment Ltd. E-mail: [email protected] United Kingdom

The unit described in the present operating instructions must be used, operated and serviced in accordance with the present instructions. Any other type of use is beyond the scope of application and can result in damage or injury to personnel, the unit or property. The unit described in the present operating instructions complies with BS EN ISO 17050-1:2010 and the EC Machinery Directive 2006/42/EC. Foreseeable Misuse of the Unit Personnel must take care when operating the unit. The following actions must be adhered to: • The maximum safe working load (SWL) must not be exceeded. • Do not travel...

Proprietor Responsibilities For the purposes of the present operating instructions the “proprietor” is defined as any natural or legal person who either uses the unit themselves, or on whose behalf it is used. In special cases (e.g. leasing or renting) the proprietor is considered the person who, in accordance with existing contractual agreements between the owner and user of the unit, is charged with operational duties. The proprietor must ensure that the unit is used only for the purpose for which it is intended and that there is no danger to life or limb of the user and third parties. Furthermore,...

Servicing and repairs All unit parts and consumables are available from STS. The unit must be fitted with original STS parts and consumables unless otherwise stated. Any deviation from non original parts and consumables may result in injury to personnel or d amage to the unit and will invalidate the warranty. The operator must never disable, remove or adjust safety mechanisms or switches. The unit should only be serviced and repaired by a competent individual as selected by the company the equipment is intended for use with. Safety devices and warning decals Safety devices, warning decals and...

Personal protective equipment (PPE) PPE must be worn at all times. A minimum of safety shoes must be worn while operating the unit. Safety shoes, safety glasses, protective gloves, hearing protection and protective overalls are to be worn when carrying out servicing, repairs and maintenance. When operating overhead loads, a hard hat must be worn. End user health and safety procedures and best practices should be followed in addition to the above recommendations. Consumables and Parts Environmental hazards Parts and oils must be disposed of in accordance with the relevant environmental protection...

In order to raise the unit safely, including off a pallet, proceed as follows: • The unit must be on a level surface to prevent it from moving accidently. • The lifting gear must only be secured to the points designated for this purpose. • Always use lifting gear with sufficient capacity. • The unit should only be handled by qualified personnel who are trained in using lifting slings and tools. • Do not walk into or stand under a raised unit. • If necessary, secure the unit with guide ropes to aid when lifting the unit. In order to jack up the unit safely, proceed as follows: • The unit must...

Unit Overview

Permitted Operating Zones The unit is designed to be used by a single operator from the rear of the unit, unless otherwise stated. All other personnel in the area where the unit is in operation must remain clear of the unit, behind the unit or within area 1 shown below. Area 1 is classed as the safe working area. Certain functions of the unit require the operator to work within area 2, the operator working within area 2 must be aware of the unit’s functions and movements along with their potential trap points. If the unit is fitted with a manual rotation handle, head controls or fitted with a...

Section II – Unit Description The STE01-DRU01 is a four-wheeled pedestrian stacker with a drum rotator band. The unit is electric-hydraulic powered with manual drum rotation. It is designed for use on level surfaces for use with drums ranging from 50 - 220 litres, steel or plastic drums with a diameter of between 350mm - 600mm. The drum should be stood vertical; the unit can then approach the drum and straddle either side. The band is pushed flush to the drum and then fastened around the drum using the ratchet and strap. Once the rim clamp is adjusted and fastened to the top lip of the drum,...

Before using this unit, operators must read and understand this instruction manual. Failure to observe the instructions in this manual will invalidate the warranty. NOTE: Personal Protective Equipment (PPE) must be worn at all times, see ‘Section I - Correct Use and Application' for more information. • Check the whole of the outside of the unit for signs of damage and leaks. Any damaged hoses must be replaced immediately. • Check the unit for visible signs of damage such as cracks, bent or severely worn parts. • Check all wheels for damage. • Check that the markings and labels are present, clean...

- Park the unit securely using the rear parking brakes and close to a 230V charging outlet. • Ensure unit is turned off. • Plug the charging cable into the socket on the control box.

- If loaded, the load must not exceed the unit's capacity. - If loaded, load undamaged. - Load at correct height for transport (< 500mm). - Flat and level ground conditions. • Disengage the rear parking brakes. • The unit can then be manoeuvred to the desired location. • Steering is controlled from the rear of the stacker using the tiller. • Travel at a constant speed. • Adapt your travel speed to the conditions of the route and the load you are transporting. • Always transport loads at as low a height as possible to retain the stability of the unit. • When finished manoeuvring, the rear parking...

- If loaded, the load must not exceed the unit's capacity. - If loaded, load undamaged. • The drum should be sitting on the floor or a pallet vertically. • Open up the arms on the rotator to the full width and move the stacker forward so that the rotator band goes around the drum. • There are two pivot points, one on each arm. These should be positioned at the middle of the drum. Manoeuvre the unit until the pivots are in the middle of the drum. • Push the two arms in so that the two pivot band sections touch the drum. • Adjust the height of the clamping band by raising or lowering the carriage...