VertiMax? Adjustable Pendant Arm
7Pages

{{requestButtons}}

Catalog excerpts

VertiMax? Adjustable Pendant Arm - 1

DATA SHEET VertiMax™ Adjustable Pendant Arm Vertically adjustable mountings for larger operator interfaces and enclosures • 13” Vertical Travel • Up to 250 pounds of Counterbalanced Lift • Ergonomic Adjustability • Locks-in-Place Automatically • 2.5” Diameter Sealed Cable Passageway Protects Cables, Keeping Them Secure and Twist-Free Heavy-duty Cast-Aluminum Construction Access covers to Cable Passage Choice of Mounting: Post Top (shown), Wall Mount, Machine Top Easily Repositioned STRONGARM’s VertiMax™ Pendant Arm allows the operator to adjust the interface to a comfortable height. The operator simply squeezes the grab handle and the interface becomes weightless and easily repositioned. The gas spring counterbalancing system automatically locks in place, providing safety and stability. Swivels at both ends with rotational stops are standard. 425 Caredean Drive · Horsham, PA 19044 · 215.443.3400 · Fax 215.443.3002 · strongarm.com ©2013 STRONGARM, Inc.

Open the catalog to page 1
VertiMax? Adjustable Pendant Arm - 2

VertiMax™ Adjustable Pendant Arm Surface Mounting Surface Mounting CTDAKI^ A D KA? 425Caredean Drive -Horsham, PA 19044 -215.443.3400 -Fax 215.443.3002 • strongarm.com

Open the catalog to page 2
VertiMax? Adjustable Pendant Arm - 3

VertiMax™ Adjustable Pendant Arm Specifications Weight/Counterbalance Capacity: Load Limitation: Diameter of Flexible, Sealed Cable Passage: Vertical Travel: Classification: VertiMax: 250 pounds VertiMax L: 160 pounds VertiMax XL: 145 pounds 600 ft/lb maximum on swivel joint 2.5” I.D. VertiMax: 13” VertiMax L: 23” VertiMax XL: 30” NEMA 4 (Also available in stainless steel NEMA 4X) Surface Mounting Selections Wall Mount Post Mount A Wall Mount VertiMax Arm attaches to a vertical surface with a thru-hole pattern (4) 0.53∅. Cables enter through the center of mounting surface or female 2½" NPT...

Open the catalog to page 3
VertiMax? Adjustable Pendant Arm - 4

VertiMax™ Adjustable Pendant Arm Assembly Configuration Selection Standard Configuration The mounting surface supports the arm and the enclosure is suspended from the arm. This is the most popular configuration. Inverted Configuration The mounting end is inverted, resulting in the arm being suspended from the mounting surface. Inverted post-mounted arms are popular for supporting the arm from the ceiling. Supported Configuration The mounting surface is supporting the arm and the enclosure is supported by the arm. A vertical extension is required for this configuration so that the arm does...

Open the catalog to page 4
VertiMax? Adjustable Pendant Arm - 5

VertiMax™ Adjustable Pendant Arm Arm Extensions Horizontal Extension The horizontal extension increases the overall length of the arm. The horizontal extension is inserted between the mounting surface pivot and the VertiMax arm. Vertical travel does not change. Middle Joint Extension The middle joint extension adds a third pivot to the VertiMax arm for in/out adjustability. Rigid Wall Mount Typically used when there is a mounting surface available but not in the ideal location. The rigid wall mount essentially moves the mounting surface. Both length and angle can be specified. These...

Open the catalog to page 5
VertiMax? Adjustable Pendant Arm - 6

VertiMax™ Adjustable Pendant Arm VertiMax Options Floorpost For use with a post top mount VertiMax arm, the floorpost is a very popular method of mounting an arm when a structural surface is not available. The 74" post is for VertiMax arms and the 79" post is for VertiMax arms with a middle joint extension. Fabricated from heavy wall 5" structural tube welded to a 12" x 12" x 1/2" thick baseplate. A 2½” female NPT coupling near the base can be specified for cable entry, additional couplings can be specified or located differently. 5" OD TubeOD Tube 5" (79" used (79" used for for Middle...

Open the catalog to page 6
VertiMax? Adjustable Pendant Arm - 7

VertiMax™ Adjustable Pendant Arm VertiMax Options (continued) Floorpost Accessories Tie-off Kit for Inverted Post A popular method of mounting is to invert a floorpost and attach it to a ceiling structure. To avoid twisting of the structure, it is recommended that diagonal tie-offs are installed. This kit includes (2) sets of clamps that attach to the post and have thru-holes for attaching user-supplied tie-offs between the clamps and ceiling structure. Release Handles Enclosure Handle Standard enclosure handle is supplied with the VertiMax Arm. The arm handle is attached to the VertiMax...

Open the catalog to page 7

All Strongarm Designs catalogs and technical brochures

  1. CleanMount

    2 Pages

  2. MightyMount?

    6 Pages

Archived catalogs