Catalogs >
STARRETT >
PROTRACTORS AND ANGLE MEASUREMENTS

PROTRACTORS AND ANGLE MEASUREMENTS
1 / 4Pages

Catalog excerpts

349 Universal Bevel No. 47 6 / 150mm This improved Universal Bevel has both offset and straight slots in the blade, in combination with straight slots in the stock that allow for a wide variety of adjustment and angle settings that are impossible to obtain with many ordinary bevels. Length of the blade is 6 (150mm), and the stock, 3-1/2 (90mm). The stock lies flat on the work or paper since the head of the clamping bolt is recessed. This tool can be set to duplicate an angle from a master, or it may be easily converted into a Bevel Protractor by using this tool with the No. 193 Protractor. Catalog No. EDP No. Blade Length 47 50266 6 Catalog No. EDP No. Blade Length 49 50267 4 (approx.) Packed one in a box. Packed one in a box. Combination Bevel No. 49 4 / 100mm Any angle may be easily transferred from one surface to another with the No. 49 Combination Bevel. This tool has a slotted blade which swings on a stud on the stock to any angle desired, and is locked in position by a knurled thumb nut. An auxiliary blade, also furnished, may be easily attached to the slotted blade and is clamped at any angle by a knurled nut. The stock is square at one end and is beveled 45º at the other. The auxiliary blade is beveled to 30º and 60º at opposite ends. Stock and blades are approximately 4 (100mm) long. The tool lies flat on the work. It may also be used with No. 193 Protractor. PROTRACTORS AND ANGLE MEASUREMENTS

Open the catalog to page 1

350 Blade Length Blade Graduations Range Catalog No. EDP No. 6 32nds, 64ths 0-180º C493 52532 C493B 52534 Protractor and Depth Gages No. 493 Series 0-180º The ability to measure angles and depths is combined in these convenient tools. No. C493 Ÿ Angular measurement is from 0-180º in opposite directions allowing the direct reading of angles and supplementary angles Ÿ Depths are measured from a 6 (150mm) blade (our No. C610N) Ÿ Both tools have a flat surface on the back of the head permitting laying the tool flat on paper or work Ÿ No-glare satin chrome finish Ÿ The No. C493 has a...

Open the catalog to page 2

351 Drill Point Gage No. 22C 59º This gage was designed specifically for use in drill grinding. It provides a quick, accurate way for determining the correct drill point angle of 59º and the correct length of drill lips necessary for clean-cut drilling at maximum feeds and speeds. Ÿ The sliding head may be adjusted to any position along the rule and locked by a thumb nut Ÿ The head is beveled to 59º (the correct drill point angle), and is also graduated in 32nds along the 59º face for measuring the drill lips which should be of equal lengths Ÿ The hook rule has accurate, machinedivided...

Open the catalog to page 3

352 Reversible Non-reversible Black Wrinkle Finish Black Smooth Finish Black Wrinkle Finish Size Blade Finish Graduation Cat. No. EDP No. Cat. No. EDP No. Cat. No. EDP No. Satin Chrome C491-12-4R 64602 C490-12-4R 52514 C12-12-4R 64290 12 No. 4R: 8ths, 16ths, C12-12-4R W/SLC* 66931 Quick Reading, 491-12-4R 52521 490-12-4R 52511 12-12-4R 50103 18 Regular 32nds, 64ths 491-18-4R 52522 490-18-4R 52512 12-18-4R 50104 24 491-24-4R 52523 490-24-4R 52513 12-24-4R 50105 300mm Regular 1/2mm & 32nds one side; 491ME-300 52524 12ME-300 50106 & 11-3/4 mm & 64ths, reverse side Bevel Protractors Nos. 490,...

Open the catalog to page 4