Group: Stanley
Catalog excerpts
GT18 4-2004 SPECIFICATIONS Stanley Hydraulic Tools 3810 S.E. Naef Road Milwaukie, Oregon 97267 Tel 503•659•5660 Fax 503•652•1780 Visit our website at www.stanley-hydraulic-tools.com Power Units Features and Benefits The new generation Stanley GT18 Power Unit is the latest in construction site hydraulic power for tools. The GT18 conforms to the Hydraulic Tools Manufacturers Association (HTMA) Type 1 and Type 2 tool circuit recommended performance. It will deliver 5 gpm or 8 gpm at pressures up to 2000 psi with heat rejection capacity exceeding the HTMA recommendation of 5 hp. Significant features of the GT18 are: • Computerized, electronic throttle control is standard on all models. The control allows for selection of constant engine speed or automatic speed. Automatic speed increases engine speed from idle when it senses tool working demand. When there is no tool working demand, engine speed GT18is returned to idle. The automatic speed mode provides lower fuel use and less noise. • All electric control system with rotary switches. • All components in the GT18 are assembled for easy routine servicing. The upper frame can be removed for more serious servicing. • A quartz hourmeter in the control panel records engine run time. • The hydraulic pump is mounted directly to the engine eliminating any misalignment and ensuring long life of the drive coupling. • An in-tank hydraulic filter continuously cleans the hydraulic fluid and assures that refill fluid passes through the filter for a clean refill. • A 35-Ah sealed, non-spillable, no-maintenance battery is located inside a covered compartment. • Moving the GT18 around is made easy with a lift-and-latch handle. • Both engine models (Briggs or Honda) have pressure lubrication systems with a pressure sensing switch that will shut down the engine if the engine oil level is too low. • Some GT18 models are available with 110 vac, 60 Hz electric power provided by a Briggs & Stratton PowerLink inverter system. This system will deliver 1000 watts, continuous and 1500 watts intermittent power through GFCI receptacles. ITEM U.S.A. METRIC OUTPUT CAPACITY 5 or 8 gpm 20 or 30 lpm PRESSURE 2000 psi 140 bar CIRCUIT TYPE Open Center HYDRAULIC RESERVOIR CAPACITY 3 gallons 11 liters FUEL TANK CAPACITY 7 gallons 26.5 liters WEIGHT (WET) 330 lbs 150 kg LENGTH 35 in. 89 cm WIDTH 21/5 in. 54.6 cm HEIGHT 29 in. 73.7 cm ENGINES Briggs & Stratton 18 hp Vanguard Honda 20 hp OHV
Open the catalog to page 1Stanley Hydraulic Tools 3810 S.E. Naef Road Milwaukie, Oregon 97267 Tel 503•659•5660 Fax 503•652•1780 All Stanley Hydraulic tools, parts, accessories and allied equipment are subject to design improvements, specification and price changes at any time without notice and with no obligation to units already sold. Weights, dimensions and operating specifications listed herein are subject to change without notice. Where specifications are critical to your applications, please consult Stanley Hydraulic Tools. Stanley Hydraulic Tools and their associated parts are warranted against defects in...
Open the catalog to page 2All Stanley Infrastructure catalogs and technical brochures
-
UNDERWATER TOOLS
7 Pages
-
MOUNTED ATTACHMENTS
7 Pages
-
HANDHELD CORDLESS TOOLS
7 Pages
-
ELECTRIC UTILITY TOOLS
15 Pages
-
RAILWAY TOOLS
19 Pages
-
HANDHELD TOOLS
23 Pages
-
CE Products
13 Pages
-
Heavy Attachments
29 Pages
-
BR50 HYDRAULIC BREAKER
2 Pages
-
DS06
4 Pages
-
CO25
2 Pages
-
GR60
2 Pages
-
CT Tools
4 Pages
-
HGE
2 Pages
-
CH15
2 Pages
-
CH18
2 Pages
-
CS05-06
2 Pages
-
BLS
2 Pages
-
Underwater Catalog
47 Pages
-
LaBounty Catalog
24 Pages
-
Stanley Infrastructure
36 Pages
-
Electric Utility
32 Pages
-
Mounted Catalog
20 Pages
-
Railroad Catalog
36 Pages
-
Hand Held Catalog
48 Pages
-
Pin Brazing / Safebonding
1 Pages
-
Large Mounted Breakers
2 Pages
-
Impact Wrenches IW16
2 Pages
-
Impact Drill ID07
2 Pages
-
Hydraulic Rail Saws
2 Pages
-
Horizontal Grinder HG80
2 Pages
-
Handheld Breakers BR67
2 Pages
-
Hydraulic Ground Rod Driver
2 Pages
-
Grinders
2 Pages
-
Frog Grinder
2 Pages
-
Environmental Padlocks
2 Pages
-
Diamond Chain Saws DS11
4 Pages
-
Cut-Off Saw
2 Pages
-
Cupstone Grinder
2 Pages
-
Catenary Maintenance
8 Pages
-
Crimping Tools
4 Pages
-
Concrete Pulverizers
2 Pages
-
Chain Saw
2 Pages
-
Bull Nose Grinder
2 Pages
-
Bucket Link Shears
2 Pages
-
HD45 underwater hammer drill
2 Pages
-
DL07652 underwater drill
2 Pages
-
90 CLASS BR87
2 Pages
-
70 CLASS BR67
2 Pages
-
40 CLASS BR45
2 Pages
-
DL07 Drill
2 Pages
-
Spike Pullers
1 Pages
-
TA57 Tamper
2 Pages
-
Mounted Breaker - MB15EXS
2 Pages
-
DROP HAMMERS
2 Pages
-
Rail Saw - RS25
2 Pages
-
Weld Shear - WS10
2 Pages
-
Robotic Welder - RW20
2 Pages
-
TracHorse - MHP1
2 Pages
-
HP08 Hydraulic Power Unit
2 Pages
-
GTR Hydraulic Power Units
2 Pages
-
Sinker Drill - SK58
2 Pages
-
Hammer Drill - HD45
2 Pages
-
Hydraverter - HV18
2 Pages
-
Core Drill - CD10
2 Pages
-
Sinker Drill - SK47
2 Pages
-
IW12
3 Pages
-
IW16
2 Pages
-
Hammer Drill - HD08
2 Pages
-
Core Drill - CD12
2 Pages
-
Rail Drill - RD12
2 Pages
-
Rail Drill - RD11
2 Pages
-
Safe Bond
2 Pages
-
Cup Stone Grinder
2 Pages
-
Drill
2 Pages
-
Profile Grinder
2 Pages
-
Underwater Grinder
2 Pages
-
Vertical Grinder
2 Pages
-
Tie Tampers
2 Pages
-
Tamper
2 Pages
-
Dewatering Pump
2 Pages
-
Trash Pump
2 Pages
-
Diaphragm Water Pump
2 Pages
-
hydraulic post driver
2 Pages
-
Hydraulic Post Puller
2 Pages
-
Earth Auger
2 Pages
-
hydraulic pruner
2 Pages
-
chipping hammer
2 Pages
Archived catalogs
-
Gas Rail Saw
2 Pages
-
Small Hydraulic Power Unit
2 Pages
-
Diamond Chain Saw
4 Pages
-
Hydraulic Breaker
2 Pages