Loading spouts
10Pages

Advantages of the Stanelle loading spout: high operating reliability protected outside bellows protected drive compact design simplied installation precisely centred material stream short loading times Stanelle Silos + Automation GmbH Langwiesenstr. 6 D -74363 Güglingen tight seat low-maintenance tel fax customisable +49 7135 9530 - 0 +49 7135 9530 -17 info@stanelle.de www.stanelle.de special sizes on request Further components: Dedusting Controlling Discharging design by andartic.de 2009 · Specications subject to modication Shut-off devices Loading Filling

Loading spouts Stanelle – always the best solution

Stanelle loading spouts – for the bulk, dust-free loading of silo vehicles, open-top vehicles, rail cars, containers, stockpiles, mixers, and ships Applications: Stanelle loading spouts are at the forefront everywhere where dust-like and granular bulk goods are loaded quickly and without detriment to the environment. Whether cement, lime, plaster, premix plaster, FGD products, pellets, grain, or other extreme bulk goods – our loading spouts operate reliably and trouble-free thanks to the careful selection of materials and their design optimised for the production processes. Advantages: High...

Further advantages: Level indicators The level indicators are essential modules serving to automate the material stream and are available in a wide range for various media. Attached lter As an alternative to the customary dedusting systems Stanelle offers the pneumatically cleaned loader lter. Owing to its direct attachment to the loader head this lter cleans the mixture of dust and air within the smallest of spaces. The cleaned lter cake is introduced directly into the silo vehicle. The exible attachment does not require any additional installation headroom. Pneumatic cleaning Although...

QUADRO The QUADRO type · for loading silo vehicles and containers · nominal width 220 mm · number of buckets 3–12 · max stroke 2900 mm · various bucket materials: steel sheet, stainless steel, plastic-lined with closure cone · optional closure cone heating Internal hoisting lines between the outside bellows and interior buckets; felt gasket to the gear chamber; square buckets suspended from two strong belts arranged opposite each other and guided over hoisting lines for greater stability. The closure cone Every practitioner knows that the closure cones on loaders are problem components:...

Only the much more resistant linkages now remain in the material stream. As replacement parts they are also easily exchangeable. The hoisting lines themselves are now attached outside of the danger zone. The choice of materials and the robust design also serve to reduce considerably the wear on the closure cone. The Stanelle closure cone is made of extremely hard wearing cast steel with solid walls 15 to 25 mm thick. The QUADRO type was developed primarily for optimising the closure cone system. square interior buckets closure cone end-to-end solution with loader lter 5

RONDO The RONDO type · for loading silo vehicles, open-topped transport, containers, stockpiles, and ships with dustlike and granular bulk goods · nominal widths 250–800 mm · number of buckets 3–14 · variant bucket materials: cast steel, steel sheet, stainless steel, plastic · mechanical level compensation · without closure cone · special sizes on request Because the hoisting lines are now attached on the outside the bellows and interior buckets can now be replaced more easily without additional hoisting gear. The interior buckets are suspended from four supporting belts. RONDO type: level...

Open-topped loading Open-topped transport can be loaded only with the RONDO type. Because the discharge cone on the QUADRO type is lifted over the closure cone there is no interim position at which the discharge would be free. The nominal width 250 (RONDO type) allows the loading of silo and alternatively open-topped vehicles when a dust dome or apron is clipped on. Larger nominal sizes require dust domes matched to each and every case. Ship loaders The JBM 500 type loader is a specialised system for loading dry, free owing bulk goods on ships. Gravel loaders The RONDO gravel loader is a...

TELE-RONDO The TELE-RONDO type · nominal width: 200 mm · throughput: 100 m³/h · telescoping length (pipe) about 2735 mm · perfected technology based on a further development of the JBM 220 QUADRO type loading spout · integrated level control automatically adjusts the loader’s telescoping length to the present ll level · variant telescoping pipe materials: steel, stainless steel The Stanelle JBM 200 TELE-RONDO type loading spout is a specialised system for loading silo vehicles (trucks, rail cars) with high-separation bulk goods like e.g. dry mortar. Bulk goods of various weights and large...

and the upstream charging or shutoff components are switched off or closed respectively. When the TELE-RONDO is raised the closure cone prevents material from escaping into the environment and circulating air – and therefore humidity – from entering the loader. QUADRO type loading Accessories The TELE-RONDO in conjunction with our transverse and longitudinal positioners presents the optimal loading solution for special bulk goods tending to separate. TELE-RONDO type loading 9