Optical Positioners Flipping Mirror/Beamsplitter Mounts 1 Optical Tables 2 Brackets & Rails 3 9 *slide M4(8-32) screws through combined M6/Ø7.4 mounting/clearance holes to mount the unit immediately to M4(8-32) holes, or mount the unit directly on any M6 tip 32 Light Test & Measurement Instruments 11 5-1 fixing screw for 1”(Ø25.4) optics 26 Translation & Rotation Stages 7 Motorised Positioners & Controllers 8 Fine Adjustment Screws Use the Flipping Mount 5F21-1 to place optics in and out of the optical scheme. Flip the platform out and back again – it sits on the adjustment screws in a repeated position. Precise alignment of various optical elements to desired angles is done by 2 adjustment screws. 3 seats form 3 kinematic points for definite position of the platform. The seats are of hardened steel. This increases the service life, as they counter the hardened steel tips of adjustment screws and pivot balls. Mount 5F21-1 has a 1” mounting hole with ∅24 mm clear aperture. A fixing screw secures the optics against 2 contact lines, 5F21-1 uses Fine Screws 9S127 (with knobs) optics stays in the experiment optics flipped down optics flipped to the side 5F21-1-SH uses Fine Screws 9SH127 (without knobs) hex key included Note: “Mirror” version is a right hand version of the standard model. Base Positioners Optical Positioners 5F21M-1 (right hand “Mirror” version) which make 2 contact points. To prevent damage to the optics, the tip of the fixing screw is made of plastic. On one side the edge of the optics stays clear. So you can use the optics close to the edge in schemes where you work with a beam very closely situated to another beam. Fine Screws 9S127 or 9SH127 come as standard (one screw has its tip modified to form a kinematic point). Depending on which side you mount the unit, you flip the platform either vertically or horizontally. By flipping out vertically the optics goes beneath the common level of the optical scheme. Still one leg of the base, with a adjustment screw on it, stays up. Yet this wouldn’t obstruct the optical path, as it wouldn’t when the optics was flipped in. Legs protruding upwards ease your access to the adjustment screws, with less risk of obscuring the beam. No need to design the legs extended down, so as to clear the space totally, like in some flippers from other ma­nu­facturers. Optical Mounts Base Mounts & Accessories 5F21-1 (left hand version) fixing screw e-mail: [email protected] – Flip optics in and out of the experiment – Repeatability 20 µrad – Kinematic design – Precise and handy angular adjustment in two orthogonal planes – Stable vertical mounting – Adjustment range of 8°  – Sensitivity of 3 arcsec – Made of black anodized aluminium – Weight 0.09 kg  – 5F21M-1 “Mirror” version

Optical Positioners *slide M4(8-32) screws through combined M6/Ø7.4 mounting/clearance holes to mount the unit immediately to M4(8-32) holes, or mount the unit directly on any M6 tip e-mail: [email protected] Base Mounts & Accessories Optical Optical Positioners Positioners 5 Miniature Flipping Mirror/Beamsplitter Mounts Base Positioners Accepts optics ∅12.7 mm (0.5 inch) ∅12.7 mm (0.5 inch) ∅25.4 mm (1 inch) ∅25.4 mm (1 inch) Note: “Mirror” version is a right hand version of the standard model. Light Test & Measurement Instruments 11 Fine Adjustment Screws Motorised Positioners & Controllers 8...

Optical Positioners Kinematic Mirror/Beamsplitter Mounts Optical Tables 2 Brackets & Rails Optical Positioners Base Positioners Translation & Rotation Stages 7 9 Motorised Positioners & Controllers 8 5MBM21-1-3SH uses three Fine Screws 9SH127 through combined M6/Ø7.4 mounting/clearance holes to mount the unit immediately to M4(8-32) holes, or mount the unit directly on any M6 tip To specify how many screws you want in a mount, append the number to the code. Suffix “SH” specifies hex screws. Examples: 5MBM21-1-3 3 screws 5MBM21-1-2 2 screws 5MBM21-1-2SH 2 hex screws Light Test & Measurement Instruments...

Optical Positioners Kinematic Mirror/Beamsplitter Mounts http://www.standa.lt e-mail: [email protected] Optical Mounts 4 Optical Optical Positioners Positioners 5 6 Base Positioners kinematic fit. A thick base adds to stability. This allowed us to eliminate part of the mount, keeping clear one edge of the optics. Useful in schemes where beams go very close to each other. As standard, we fit screws 9S127. You may order the mounts with 2 or 3 adjustment screws. Choose any screw and removable knob found in section 9. Base Mounts & Accessories optics against 2 contact lines, which make 2 contact points....

Optical Positioners Mounts with hard seats Optical Tables 2 Brackets & Rails 3 4 Optical Mounts 5 6 Optical Positioners Base Positioners Translation & Rotation Stages 7 9 Motorised Positioners & Controllers 8 Fine Adjustment Screws OptoMechanics & Sets 10 Light Test & Measurement Instruments 11 Specifications Tilt/tip range Sensitivity Travel range Sensitivity Optics diameter Clear aperture Weight 5MBM22S A screw pushes via a seat of hardened stainless steel or sapphire. Mounts 5MBM22S, 5MBM22SP have a 1” and 2” mounting hole. A fixing screw secures the optics against 2 contact lines, which make...

Optical Positioners True Gimbal Mount gimbal axis Base Mounts & Accessories clear aperture Light Test & Measurement Instruments 11 *Dependence between actuators’ movement and angular displacement of optical element is not linear. 1,25 µm 0,156 µm 0.25 mm 1 µm 4 mm/s 1.2 m length cable included HDB15(M) 0.7 kg Fine Adjustment Screws Motorised Positioners & Controllers 8 for M6(1/4-20) screw 2 clearance slots Motorized version 8MGM25T-1 Optics diameter Clear aperture Angular range Type of actuator Resolution* in full step in 1/8 step Lead screw pitch Repeatability Maximum speed Cable Motor connector...