CATALOG TABLE OF CONTENTS SPRA YING SYSTEMS CO . CATALOG 75TJ | T A N K J E T ® T A N K C L E A NING PROD UCTS North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA Tel: 1.800.95.SPRAY Intl. Tel: 1.630.665.5000 Fax: 1.888.95.SPRAY Intl. Fax: 1.630.260.0842 Email: [email protected] www.spray.com Catalog 75TJ © 2018 Spraying Systems Co. All rights reserved. Full protection of law claimed under Universal Copyright and Berne Conventions and other applicable national and international laws. TA NKJE T ® TANK CLEANING PRODUCTS

TANKJET ® FROM SPRAYING SYSTEMS CO.: THE PRODUCTS, EXPERTISE & SERVICES TO OPTIMIZE TANK CLEANING It takes more than equipment to ensure proper cleaning of your tanks, totes, vats, drums and more. It takes experience and expertise in addition to an extensive product line. The ultimate goal is to ensure tanks are cleaned thoroughly, in the least amount of time, using the least amount of water/chemicals possible. The right partner will guide you through the entire process, from equipment selection, to system evaluation and optimization, and ongoing support. We’re that partner. We have dozens of...

Technical Reference

TECHNICAL REFERENCE TANKJET ® QUICK REFERENCE GUIDE Spray Coverage Recommended Strainer Mesh (micron) Operating Principle Fluid-driven turbine Fluid-driven turbine Fluid-driven turbine Fluid-driven turbine Fluid-driven turbine Fluid-driven turbine Fluid-driven reactionary force Fluid-driven turbine Fluid-driven reactionary force Fixed stationary 360° and custom spray angles Fluid-driven constant speed

TANKJET ® QUICK REFERENCE GUIDE TECHNICAL REFERENCE Operating Principle Spray Coverage Recommended Strainer Mesh (micron) Fluid-driven constant speed Fluid-driven reactionary force Fluid-driven reactionary force Fixed stationary Fluid-driven turbine Fixed stationary Fluid-driven reactionary force Fluid-driven reactionary force Fluid-driven reactionary force Fluid-driven reactionary force Fixed stationary Fluid-driven reactionary force Fluid-driven reactionary force

TECHNICAL REFERENCE OPTIMIZING TANK CLEANING OPERATIONS CLEANING POWER GUIDELINES Choosing a tank cleaner is based primarily on tank size and level of cleaning required. Understanding the definitions that follow will help ensure you select the right tank cleaner for your application. High-impact cleaning is required to remove stubborn residues such as layers of a dried substance. Tank cleaners in this category generally use high pressure and/or high flow and spin at slow rotational speeds to maintain high impact. Solid stream nozzles are used to maximize impact. Medium-impact cleaning is required...

TECHNICAL REFERENCE OPTIMIZING TANK CLEANING OPERATIONS SPRAY DISTANCE Tank Diameter Range Feet

TECHNICAL REFERENCE TANK CLEANING OPTIMIZATION CHECKLIST OPTIMIZING YOUR TANK CLEANING OPERATIONS Tank cleaning equipment is designed to yield specific performance under specific conditions. A variety of factors can affect results. Even when tank cleaning equipment appears to be working as expected, there may be room for improvement. Adjustments are often possible to achieve more consistent results, improve efficiency, reduce the length of time tanks are out of service and lower operating costs. Here are seven optimization tips to consider as you evaluate the current performance of your tank...

TANK CLEANING OPTIMIZATION CHECKLIST TECHNICAL REFERENCE 6. REVIEW SYSTEM COMPONENTS 4. SHORTEN CLEANING TIME BY INCREASING IMPACT Simple adjustments to liquid pressure and flow may enable a reduction in the number of cycles needed for thorough cleaning. Faster cleaning saves time and reduces water and chemical use. To increase impact and cleaning efficiency, it’s far more effective to increase flow than liquid pressure since increasing flow rate intensifies impact at a greater rate than increasing pressure. In fact, doubling flow rate boosts impact as much as 100% while doubling liquid pressure...

TECHNICAL REFERENCE TANK CLEANING CASE STUDIES OPTIMIZING TANK CLEANING WILL PAY FOR ITSELF QUICKLY. HERE ARE A FEW EXAMPLES: PHARMACEUTICAL MANUFACTURER REDUCES CLEANING TIME BY 80% TOTE CLEANING TIME REDUCED FROM 45 MINUTES TO 10 MINUTES Before: Spray balls were used to clean two 6.25 ft dia. x 9 ft tall (1900 mm diameter x 2790 mm tall) processing tanks. Before: Turbine-driven rotating nozzle spraying hot water at 10 gpm (37.8 lpm) at 100 psi (6.9 bar). Wash cycle was often repeated a second time for complete removal of residue. After: A TankJet® AA190, equipped with a 1 ft. (317 mm) shaft,...

PAINT TANKS CHEMICAL TANKS ADHESIVE TANKS TANKER TRUCKS BROKE CHESTS BLENDERS WINE VATS PROCESS TANKS FOOD AND BEVERAGE TANKS BREWERY TAN

CLEAN HARD-TO-REMOVE RESIDUES WITH HIGH-IMPACT, HIGH-EFFICIENCY SPRAYS IDEAL FOR CLEANING LARGE TANKS Designed to clean large vessels, these tank cleaners deliver high-impact, high-efficiency sprays for the complete removal of contaminants and residues. Designed to provide effective cleaning in the least amount of time possible, TankJet® 360, AA290, 180 and 80 tank cleaners ensure tanks are returned to service quickly.

QUICK REFERENCE GUIDE Cleaning Power Operating Principle Flow Rate Range gpm (lpm) Max. Spray Temperature Coverage °F (°C) Page Number High impact Gears – 17-4PH stainless steel Gear shaft bearing system – PTFE or oilite bearing O-rings – self-lubricating EPDM or Viton® Seals – high-performance spring-energized PTFE All other metallurgy – 316 stainless steel High impact Seals – PTFE fluoropolymer resin All other metallurgy – 316 stainless steel Gears – 17-4PH stainless steel O-rings – self-lubricating EPDM or Viton Seals – high-performance spring-energized PTFE Gear shaft bearing system – PTFE...

TANKJET ® 360 TANK CLEANER TANKJET 360 TANK CLEANER FEATURES AND BENEFITS • Provides consistent, high-impact, high-efficiency cleaning over the entire pressure range for short cycle times IMPACT SPRAY COVERAGE • Can be used for high-concentration chemical recirculation cleaning or low-pressure, high-volume cleaning • Choice of dual- or triple-nozzle fluid-driven hubs in food-grade, oil-lubricated or flow-through gearbox designs • Nozzles rotate 360° in horizontal and vertical planes, creating a crisscrossing pattern to thoroughly clean tanks and remove the stickiest of residues MOUNTING OPTIONS...