DISC SPRINGS

Disc Springs are conically-shaped, washer-type components designed to be axially loaded. What makes Disc Springs unique is that based on the standardised calculations of DIN EN 16984 (formerly DIN 2092), the deflection for a given load is predictable and the minimum life cycle can be determined. Disc Springs can be statically loaded either continuously or intermittently, or dynamically subjected to continuous load cycling. They can be used singly or in multiples, stacked parallel, in series or in a combination thereof. The advantages of Disc Springs compared to other types of springs include...

standard product range STANDARD RANGE SPIROL offers the full range of DIN EN 16983 (formerly DIN 2093) Group 1 and 2 Disc Springs in Series A, B, and C. In addition to the DIN specified sizes, SPIROL stocks its own standard size range in outside diameters from 8mm to 200mm in order to meet the diverse needs of the customer. SPIROL Standard Disc Springs meet all material, dimensional tolerance, and quality specifications as laid out in DIN EN 16983 (formerly DIN 2093) but in diameter and thickness combinations that are not included in the DIN standard. See page 15 for SPIROL’s offering. SPECIALS...

DEFLECTION AND LOAD CHARACTERISTICS THEORETICAL VERSUS MEASURED DEFLECTION 8000 At the lower range, the actual measured curve departs slightly from the theoretical due to residual stresses. In the mid range – the usual working range – the actual measured deflection very closely coincides with the theoretical. Measured Characteristic As the deflection increases, the force moment arm shortens and the force required increases sharply. When the s/ho ratio exceeds 0.75, the deviation from the theoretical increases sharply. Accordingly, force/deflection predictability is limited to 75% of total deflection...

LOADING STRESSES CRITICAL STRESS POINTS When a Disc Spring is loaded, compressive stresses are generated at Points I and IV. Compressive stresses typically act on the upper surface of the Disc. At the theoretical Point (0) between Points I and IV, the stress must not exceed the yield strength of the Disc material (1,400 – 1,600 MPa for the specified materials) to ensure that there will be no permanent deformation (set). Tensile stresses at Points II and III are the basis for fatigue life calculations. Tensile stresses typically act on the lower surface of the Disc. STATIC LOADING Static loading...

The process to estimate fatigue life for a Disc Spring is iterative in nature. It is not possible to select a fatigue life and then work backward to arrive at a Disc Spring configuration. The basic steps to estimating fatigue life are as follows: Determine the application requirements in the least loaded state. This should specify the force required for the Disc Springs to exert in the minimally compressed condition. Determine the fully loaded condition of the Disc Spring. This may be specified by a length of travel or an additional load that will be exerted on the Disc Spring. Using the above...

FATIGUE LIFE The charts below represent typical expected life of Discs tested under laboratory conditions. To use these charts properly, it is necessary to determine the stresses at both minimum and maximum deflection points of the Disc. Tensile stresses are always the determining factor in causing failure due to fatigue, so as a minimum, evaluating the stresses at Points II and III is required. It is recommended that both be evaluated and the worst case used. GROUP 2 1.25mm ≤ t ≤ 6.0mm Maximum tensile stress at selected point, MPa Maximum tensile stress at selected point, MPa These values are...

design guidelines SPIROL sizing and selection fatigue life • Select the disc with the largest outside diameter (D„). This reduces the stresses at a given force (F)/deflection (s) ratio and thus enhances fatigue life. An outside (De) to inside diameter (Di) of 1.7 to 2.2 also enhances performance and longevity. • Select a disc that achieves the maximum force required at less than 75% of its deflection. Deflection of 75% of cone height (ho) should be the design maximum. Reducing deflection increases fatigue life. • Force/deflection curves can be changed by varying the cone height (ho) to thickness...

Stacking individual Disc Springs provides the designer with: • A wide range of possible force/deflection combinations; • The ability to design application specific load curves – both progressive and regressive; and • The opportunity to design a range of dampening characteristics into the design. DISC SPRINGS – STACKING Deflection: Same as single Disc Force: Single Disc multiplied by the number of Discs Deflection: Single Disc multiplied by the number of Discs Force: Same as single Disc Deflection: Single Disc multiplied by the number of Discs in series Force: Single Disc multiplied by the number...

disc springs - stacking pre-assembled SPIROL offers Pre-Assembled Disc Spring Stacks (greased or ungreased) in custom configurations packaged in shrink wrap with a perforated tab for ease of insertion into the assembly. This saves time and helps to mistake-proof the assembly process. STACK GUIDANCE Stacks need to be guided to keep the discs in position. The preferred method is internal, such as a rod through the inside diameter. In case of external guidance, a sleeve is suggested. In either case, the guiding component should be case-hardened to a depth of not less than 0.6mm and a hardness of...

dimensional tolerances diameter tolerance Outside Diameter: De h12 Concentricity: De < 50mm 2 • IT 11 The static load (F) of a single disc shall be determined for a disc in the loaded state using a suitable lubricant. The pressure plates between which the disc is compressed must be hardened, ground and polished.

TO ORDER: Product / De x Di x t / material code / finish code EXAMPLE: DSC 25 x 12.2 x 0.7 BR Refer to page 15 for SPIROL Stainless Steel Disc Springs. STANDARD MATERIALS