Using the toggle principle, the quick clamping tools have decisive advantages: •The clamping lever is opened so as to completely clear the work surface, so that the work piece can be extracted from and/or placed in the equipment without difficulty (fig.1). • A small shift of the control lever is sufficient to bring the control lever to the work piece. The placement of three pivots (fig.2) clearly shows that the force exerted by the clamping lever is transmitted to the control lever. • In the fig.3 position, when the three pivots are aligned the maximum Fs clamping force is obtained (dead centre...

TABLE OF CONTENTS 10 VERTICAL A-E LATCH TL-TFL LATCH ACCESSORIES PUSH AND PULL STRAIGHT-LINE ACTION AS HEAVY PUSH AND PULL STRAIGHT-LINE ACTION AS HORIZONTAL NL-PL ONLY PUSH STRAIGHT-LINE ACTION AS VERTICAL ELS-FLS VERTICAL AV-EV LONG LIFE LSC-LSG HORIZONTAL ML-OL PUSH AND PULL STRAIGHT-LINE ACTION ASD-ASS VERTICAL BL-FL LONG LIFE LLB-LLF PUSH AND PULL STRAIGHT-LINE ACTION ASD-ASS LONG LIFE LLA-LLE VERTICAL AL-EL LONG LIFE ACCESSORIES

NEOPRENE SPINDLE ARTICULATED SPINDLE FLANGED WASHERS 78 BOLT RETAINER BAND PNEUMATIC LPV REINFORCED HEAVY PNEUMATIC EPVM HEAVY SPRING SPINDLE LATCH ROTATIONAL ERGONOMIC HANDLE LATCH ACCESSORIES HORIZONTAL ROTATIONAL RIGID SPINDLE

AISI 304/316 STAINLESS STEEL INDEX ARTICULATED SPINDLE LATCH ACCESSORIES HORIZONTAL NX-PX LATCH TX-TFX BOLT RETAINER BAND HORIZONTAL MX-OX PUSH AND PULL STRAIGHT-LINE ACTION ASX VERTICAL ALX-ELX LATCH ACCESSORIES

POSSIBLE APPLICATIONS

VERTICAL SERIES The clamping and control levers move in the same direction. When clamping is obtained, the control lever is in the vertical position. The light version of the series presented in this catalogue has a retaining force between 75 and 875 daN, while the heavy version has a retaining force between 1000 and 3000 daN. The heavy version is used when highly intense resistant forces are used, for example when closing jigs for foams, polyurethanes, etc. The clamp of this series are built to be easily disassembled for reworking of the individual elements depending on the requirements of use....

VERTICAL SERIES VERTICAL SERIES WITH FOLDED BASE Some sizes of this series are also produced in stainless steel and are shown below in red. Material: Galvanized steel or AISI 304 stainless steel Riveted pivots: Galvanized steel or AISI 304 stainless steel Supporting bushes: Hardened and ground steel (for sizes ≥130) Handles: Red polyurethane; resistant to oils, grease and other chemical agents. Performance: Form A and form AX with open clamping lever and two flanged washers. Form E and form EX with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles:...

VERTICAL SERIES VERTICAL SERIES WITH STRAIGHT BASE Some sizes of this series are also produced in stainless steel and are shown below in red. Material: Galvanized steel or AISI 304 stainless steel Riveted pivots: Galvanized steel or AISI 304 stainless steel Supporting bushes: Hardened and ground steel (for sizes ≥130) Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form B and form BX with open clamping lever and two flanged washers. Form F and form FX with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles:...

VERTICAL SERIES VERTICAL SERIES WITH FOLDED BASE AND ANTI-RELEASE LEVER Some sizes of this series are also produced in stainless steel and are shown below in red. Material: Galvanized steel or AISI 304 stainless steel Riveted pivots: Galvanized steel or AISI 304 stainless steel Supporting bushes: Hardened and ground steel. Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form AL and form ALX with open clamping lever and two flanged washers. Form EL and form ELX with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles: To...

VERTICAL SERIES VERTICAL SERIES WITH STRAIGHT BASE AND ANTI-RELEASE LEVER Some sizes of this series are also produced in stainless steel and are shown below in red. Material: Galvanized steel or AISI 304 stainless steel Riveted pivots: Galvanized steel or AISI 304 stainless steel Supporting bushes: Hardened and ground steel. Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form BL and form BLX with open clamping lever and two flanged washers. Form FL and form FLX with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles: To...

RoHS COMPLIANT VERTICAL SERIES WITH ANTI-RELEASE LEVER AND EXTENDED CLAMPING LEVER Material: Galvanized steel Riveted pivots: Galvanized steel Supporting bushes: Hardened and ground steel Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form ELS with extended clamping lever and folded base. Form FLS with extended clamping lever and straight base. Spindles: To be ordered separately (see Accessories on page 76). Extensions: The models are supplied with AP6 and AP8 extension as per the drawing and with two flanged washers (see Accessories on page 79). Features...

VERTICAL SERIES VERTICAL SERIES WITH FOLDED AND FRONT BASE Material: Galvanized steel Riveted pivots: Galvanized steel Supporting bushes: Hardened and ground steel Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form AV with open clamping lever and two flanged washers. Form EV with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles: To be ordered separately (see Accessories on page 76). Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against...

VERTICAL SERIES VERTICAL SERIES WITH STRAIGHT AND FRONT BASE Material: Galvanized steel Riveted pivots: Galvanized steel Supporting bushes: Hardened and ground steel Handles: Red polyurethane resistant to oils, grease and other chemical agents. Performance: Form AVF with open clamping lever and two flanged washers. Form EVF with full clamping lever and bolt retainers to be welded in the desired position and angle. Spindles: To be ordered separately (see Accessories on page 76). Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against...