Southco® Captive Fasteners Polished, Spring-ejected Series, M3 Thread • Highly polished appearance 17 THREAD SIZE (see table) RETAINER ØH (before knurl) SHIPPED UNASSEMBLED. YOUR OUTER PANEL THICKNESS MIN. Caution: Do not exceed 0.4 N•m tightening torque when fastening. THREAD SIZE PART NUMBERS BLACK screw assemblies 1.3 BRIGHT POLISHED screw assemblies 1.7 2.5 Captive Fasteners Captive Screws Note: Each part number represents a screw and standoff shipped unassembled, protectively packaged (bright standoffs are bulk packaged). Material and Finish SCREW: 302 Stainless steel. STANDOFF: 305 Stainless steel. BOTH PARTS are passivated or are passivated plus black organic coating. SPRING: 302 Stainless steel. RETAINER: Natural color nylon. To Install Standoff STANDOFF Your outer panel thickness Insert standoff into hole and flare into countersink as shown. BACK-UP TOOL FLARING PUNCH Standoff Installation Tools Insert screw (with spring and retainer) into standoff. (Order separately). PART NUMBER 54-0-5467-11 Assemble seating end of spring into recess retainer. Material Hardened steel. • Products identified with this symbol are stocked subject to prior sale in one or more of our global locations. Press to snap retainer into standoff. Hardened steel. millimeter (inch) millimeter (inch) Dimensions without tolerances are for reference only. If unavailable from our facility nearest you, allow for shipping tim

Southco® Captive Polished, Spring-ejected Series, 4-40 and 6-32 Thread • Highly polished appearance Fasteners Caution: Do not exceed 3-1/2 in.-lb. tightening torque when fastening Material and Finish NO. 4 SCREW: 303 Stainless steel. NO. 6 SCREW: 302 Stainless steel. STANDOFF: 305 Stainless steel. SCREWS and BLACK screw assemblies OUTER PANEL THICKNESS BRIGHT POLISHED screw assemblies your OUTER PANEL THICKNESS STANDOFFS are passivated or are passivated plus black organic coating. SPRING: 302 Stainless steel, passivated. RETAINER: NO. 4 size, natural color nylon; No. 6 size, black nylon. Fasteners...

Southco® Captive Fasteners Polished, Spring-ejected Series, M4, IVI5 and IVI6 Thread • Highly polished appearance To select proper screw assembly 1. Measure your outer panel thickness and enter SCREW ASSEMBLY SELECTION TABLE (right) with your thickness. 2. Read across to find P dimension and installation method (A or B). 3. Enter ASSEMBLY PART NUMBER TABLE (right) with your P dimension, at section having your desired thread size, and read across to find correct assembly part number. Captive Fasteners Captive Screws BLACK screw assemblies Note: Longer screw lengths and unslotted head styles are...

To Captivate Screw 1. Slip spring over shank of screw. Spring must 2. Insert screw (with spring) through hole be oriented as shown in diagram. in standoff. Split Ring Retainer M6 spring. Single coil end toward screw 4. Hold screw head and rotate tool until retainer is threaded onto throat of screw. SCREW THREAD SIZE Installation Tools (Order separately). for larger metric spring-ejected NO. 53 assemblies For Retainers Captive Fasteners Captive Screws For StandoffV. 90-2824-11 • Hardened steel. • Products identified with this symbol are stocked subject to prior sale in one or more of our...

Southco® Captive Fasteners Polished, Spring-ejected Series, 8-32,10-32 and 1/4-20 Thread • Highly polished appearance THREAD rSIZE (see table) SHIPPED UNASSEMBLED To Select Proper Screw Assembly 1. Measure your outer panel thickness and enter table (below) with your thickness. 2. Read across to find P dimension and installation method (A or B). 3. Enter part number table with your P dimension and read across to find correct Slotted BLACK screw assemblies assembly part number under head and thread size desired. Captive Fasteners Captive Screws Screws will fully retract Installation To Install...

Southco® Captive Fasteners Polished, Spring-ejected Series, 8-32, 10-32 and 1/4-20 Thread Installation Split Ring Retainer SCREW THREAD SIZE Installation Tool for Retainers PART NUMBER To Captivate Screw 1. Slip spring over shank of screw. Spring must be oriented as shown in diagram. 2. Insert screw (with spring in place) through hole in standoff. 3. Insert retainer into recess in end of tool. 4. Hold screw head and rotate tool until retainer is threaded onto throat of screw. Captive Fasteners Captive Screws Standoff Installation ToolsV. southcor FLARING PUNCH PART NUMBER | 90-2824-11* Material...

Southco® Captive Fasteners Polished Series, M3 Thread • Simple design • Highly polished appearance i—THREAD SIZE (see table) To select proper screw measure your outer panel Enter table with your thick YOUR OUTER PANEL THICKNESS THREAD SIZE PART NUMBERS Thread screw through hole in top surface of standoff. BLACK screw assemblies Bring panels together. Captive Fasteners Captive Screws To Install Standoff 1. Insert stand off into hole and flare into countersink as shown. BRIGHT POLISHED screw assemblies Thread screw tightly into frame until undersurface of screw head completely flattens the raised...

Southco® Captive Fasteners Polished Series, 4-40 and 6-32 Thread • Simple design • Highly polished appearance BLACK screw assemblies OUTER PANEL THICKNESS BRIGHT POLISHED screw assemblies OUTER PANEL THICKNESS 1. Thread screw through hole in top surface of standoff. 2. Bring panels together. Thread screw tightly into frame until under surface of screw head completely flattens the raised helix. Withdraw screw to ensure it is fully captivated. Material and Finish NO. 4 SCREW: 303 Stainless steel NO. 6 SCREW: 302 Stainless steel. STANDOFF: 305 Stainless steel. SCREWS and STANDOFFS are passivated. BLACK...

Southco® Captive Fasteners Polished Series, M4, M5, and IVI6 Thread • Simple design • Highly polished appearance rTHREAD SIZE (see table) SHIPPED UNASSEMBLED Captive Fasteners Captive Screws Your Outer Panel Thickness Select an assembly with P dim. of: To Select Proper Screw Assembly 1. Measure your outer panel thickness and enter SCREW ASSEMBLY SELECTION TABLE (right) with your thickness. 2. Read across to find P dimension and installation method (A or B). 3. Enter ASSEMBLY PART NUMBER TABLE (right) with your P dimension, at section having your desired thread size, and read across to find correct...