SP14T Antenna Switch Module for 12TRx/2Tx with 4bit parallel I/F CXM3614ER Description The CXM3614ER is a SP14T antenna switch module for GSM / UMTS / CDMA / LTE multi-mode handset. The CXM3614ER has a built-in dual low pass filter and a +1.8V CMOS compatible decoder. The Sony GaAs junction gate pHEMT (JPHEMT) MMIC process is used for low insertion loss and high linearity. The device has low BOM with no DC blocking Capacitor. (Applications: GSM/UMTS/CDMA/LTE multi-mode handset) 0.50dB (Typ.) TRx (Cellular Band) 0.70dB (Typ.) TRx (IMT Tx Band) High Linearity: Small Package Size: Lead-Free and RoHS Compliant Structure GaAs Junction Gate pHEMT (JPHEMT) MMIC Switch, CMOS Decoder This IC is ESD sensitive device. Special handling precautions are required. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits

Block Diagram of SP14T Antenna Switch Module Decoder Logic

Truth Table State *1)State “L” means a switch “OFF”, state “H” means a switch “ON”.

Absolute Maximum Ratings Symbol/conditions Minimum Maximum Unit Supply voltage Control voltage Input power Operating temperature Storage temperature

Electrical Characteristics VDD =2.5V, Ta=25℃ Item Insertion Loss

Path All ports in Active Paths Inter modulation product power in Rx band Switching　Time Supply Current Control Current

Electrical Characteristics are measured with all RF ports terminated in 50 ohms. *1 Pin = 25dBm, 704 to 787 MHz (Band 13, Band 17) *2 Pin = 26dBm, 824 to 960 MHz (Band 5, Band 8) *3 Pin = 26dBm, 1710 to 1990 MHz (Band 1 Tx, Band 2, Band 3, Band 4 Tx) *4 Pin = 10dBm, 2110 to 2170 MHz (Band 1 Rx, Band 4 Rx) *5 Pin = 26dBm, 2300 to 2400 MHz (Band 40) *6 Pin = 26dBm, 2500 to 2690 MHz (Band 7) *7 Pin = 35dBm, 824 to 915 MHz (GSM 850/900 Tx) *8 Pin = 32dBm, 1710 to 1910 MHz (GSM 1800/1900 Tx) *9 Pin = 10dBm, 869 to 960 MHz (GSM 850/900 Rx) *10 Pn = 10dBm, 1805 to 1990 MHz (GSM 1800/1900 Rx) *11 Measured...

Triple Beat Ratio VDD = 2.5 V, Ta = 25 °C Item Triple Beat Ratio *1 Jammer at Ant Triple Beat -30 dBm Product at TRx*1 Electrical characteristics are measured with all RF ports terminated in 50 . Measured with the recommended circuit Electrical characteristics are measured with all RF ports terminated in 50 . Measured with the recommended circuit

Recommended Circuit *1: No DC blocking capacitors are required on all RF ports. *2: DC levels of all RF ports are GND. *3: L1(22nH) and C1(22pF) are recommended on Ant port for ESD protection. *4: C2 Capacitor (100pF) is recommended .

VQFN-26P-02 Macro drawing (Reference) ■PKG : 3.2mrn>:2.8mm tMeta I mask "thickness : 1 1 0 (1 m Mask (Open area) Resist {Open area)

1 2 II WIDTH EMBOSSED TAPING HATEtIAL:POLYSTYRENE CONTAINING CARBOH [ANTISTATIC! tINTRODUCTION OF REUSE REEL I.EEEL THAT IS USED AGAIN AFTER COLLECTION) IE USE THE REUSE REEL OF JEITA SPECIFICATION.

Revision History Status Revised Date Revised Contents Initial Datasheet Ratings table, Electrical characteristics table Add footer on P1, add GND symbol at package back side 0.3 Fixed IL item Moved Changed IL table by port, Add VSWR, change Harmonics limits 0.5 Change Attenuation limit(ANT-TX1 high freq), Add revision history Change Bias condition Vctl(L) Change Attenuation (ANT-TX1 freq) (ANT-TX2 limit 5GHz) Change IL(TRx12, TX2) Change Isolation table Add Harmonics,IMD,IP3 path condition Delete “Target Specification of” at TBR, IIP2 specification and change tables. Change IIP2 Jammer condition....