GUARDPRO
15Pages

Operation and Maintenance Documentation SONNIGER Polska Sp. z o.o. Sp.K. ul. Śląska 35/37, 81-310 Gdynia, Poland, infolinia 801 055 155, tel. + 48 58 785 34 80, www.sonniger.com Sąd Rejonowy Gdańsk-Północ, VIII Wydział Gospodarczy Krajowego Rejestru Sądowego, KRS 0000504509, NIP 586 227 35 14,Regon 22154369 kapitał zakładowy: 1.655.

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 1. PURPOSE OF THE DEVICE The industrial air curtain is intended to be used in regions with a moderate and cold climate, in spaces where temperature ranges from -15 to +40°C and of relative humidity up to 80% (at the temperature of +25°C), in conditions free from external factors such as pollens, hydrometeor (horizontal precipitation) and chemical vapors. In winters, air curtains protect against heat loss in rooms which is possible due to the airstream suitably directed that protects the entrance of cold air into a...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 3. HEAT OUTPUT RANGES GUARD PRO 150-200 W Air curtains with water heater GUARDPRO industrial air curtians are equipped with modern and safe solution based on PTC electric heaters. Main advantages of PTC electric heaters No current on coil surface ill Lower temperature on coil surface in comparison to old type of electric heaters (for ex. electric wires), long life solution Large space of PTC coil, enhanced energy exchange between coil and air. ill Fully automated regulation of heat capacity depending on air flow ill...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 4. GENERAL AND SAFETY PRINCIPLES The GUARD PRO air curtains are manufactured in compliance with the rules and standards concerning quality, ecology, utility and work comfort . Before starting the device be sure to read the Manual carefully. The GUARD PRO air curtains are delivered ready-to-use in a cardboard package that is to protect from any mechanical damages. The package consists of: the device, the Manual (Operation and Maintenance Documentation) and the Guarantee. If the optional automatic control ordered, it...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 5. ASSEMBLY Before mounting the unit, take into consideration the followings: accessibility/easy access for any servicing and maintenance works access to water and electrical installation possibility to mount the curtain directly at the gate entrance It is advisable to mount the device to the wall or the ceiling above the doorway on supporting mount pins or supporting constructions ( shapes and dimensions of the supporting construction may be individually designed in compliance with durability and strength...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 Vertical assembly: To mount the curtain horizontally in a proper way, keep the distance of min 300mm from the rear side of the device. To mount the GUARDPRO curtain to the ceiling, use the GUARDPRO multi-purpose connector. Mounting pins of diameter 11 may be attached to the connector (not included in the delivery). To mount the curtain vertically make sure the air outlet of the curtain is as close as possible to the doorway and air gap is at the height of the upper edge of the entry. Please, make sure to keep the...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 7. ELECTRICAL CONNECTION DIAGRAMS To connect the curtain use a 3-core copper cable of minimal diameter 3x1,5mm² for two curtains (up to 6 fans) or 3x2,5mm² for 3 curtains (up to 9 fans). The electrical installation and connection to power supply must be done in compliance with the existing regulations and standards for building industry. The electric network, to which the device is to be connected, should protect the device against overloading and short circuit. It is necessary to use protective grounding. Any...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 7.2 Connection scheme for GUARDPRO W (water coil) and C (without coil) with CONTROLBOX S3 and SPEEDER S2 or SPEEDER S3 speed regulator. NOTICE! A dashed line indicates factory-mounted jumpers that enables the operation of CONTROLBOX S3 without SPEEDER speed regulator. When installing the SPEEDER controller, jumpers must be taken out. NOTICE! DURING CONNECTION OF MAIN ELECTRICAL SUPPLY OF CONTROL BOX, POLARITY (L-N CONNECTION) MUST BE KEPT AS PRESENTED ON ABOVE SCHEME. L-N CONNECTION CANNOT BE MIXED (CONNECTED IN...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 Electrical connection scheme for GUARDPRO E (electric heater) Before starting of electrical connection please veryfy if power supply and frequency corresponds to requirements of GUARDPRO (presented on product stikcer and techncial manual) GUARDPRO are equipped with singe phase fans (1~230 V/50 Hz) it is required to use additional protection for overload and shor circuit. It is not allowed to start up GUARDPRO without grounded line. NOTICE! Supply of electrical heaters 3 x 400V/50 Hz GUARDPRO 150E – supply wires min 5...

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 7.4 Connection scheme for GUARDPRO E (electric heater) with CONTROLBOX S3 and SPEEDER S2 or SPEEDER S3 speed regulator. connection box for e ectrica heaters connection box for e ectrica heaters ocated on GUARDPRO unit ocated on GUARDPRO unit GUARDPRO PK = K2 DOOR STOP Main fuse Management system fuse F2- 16 A

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 8. DIMENSIONS GUARD PRO 150W, GUARD PRO 150C, GUARD PRO 150E, GUARD PRO 200W, GUARD PRO 200C, GUARD PRO 200E

Operation and Maintenance Documentation of GUARD PRO air curtains v201708 9. OPERATION AND MAINTENANCE The engine and fan used in the GUARD PRO air curtains are maintenance-free devices but regular check-ups are advised, especially motor and bearing (fan’s rotor should rotate freely, free from any axial and radial throws/run-outs and undesired knocks/rattles. The heat exchanger requires systematical cleaning all dirts /impurities off. Before the start of the heating period, the heat exchanger is advised to be cleaned with compressed air directed to the air outlets; there is no need for...