ALL IN ONE CND TESTING

Product catalog summary

Overview
The document describes the "All-in One" non-destructive testing (NDT) instrument by Solgeo, designed for sonic and ultrasonic testing of materials such as concrete, masonry, and stone. It is suitable for both in-situ and laboratory testing, including "cross hole" and "Pile Integrity Test" (PIT) for piles and diaphragm foundations.

Applications

Verification of concrete elements on-site
Analysis of diaphragms and foundation piles
Seismic cross-hole test

Technical Characteristics

Channels: 2 input / 1 transmitter
Converter: 2 channels 12bit A/D converter
Input: Differential / Single ended / IEPE
Input range: +/- 5 Vpp
Amplification: 1 to 40000, software selectable
Sample rate: 10KHz to 12.5 MHz
Resolution: 12 [email protected] to >16bit@50KHz
Transmitter drive voltage: 100V to 1200V
Pulse duration: Selectable 1 to 65000 μs
WiFi connectivity: 802.11 (100m)
Power supply: Internal battery LiFePO4 (4.5Ah)
Autonomy: > 35 hours standby / 20 hours working
Case: IP 65
Working temperature: 0-60°C
Size and weight: 320x212x96mm, 2.5 kg

Kits and Accessories

Kit Contact: Complies with UNI EN 12504-4, ASTM D2845-08, ASTM C597-02. Includes 55 kHz or 20 kHz piezoelectric receivers and a hammer-transducer.
Kit PIT: Complies with ASTM D5882-07. Includes PIT-Hammer and Accelerometer for low strain integrity and echo methods.
Kit MCHA: Complies with ASTM D6760-16. Allows cross-hole measurements along three paths in pile foundations with synchronization impulse using an encoder.

Contact Information
For further inquiries, contact Solgeo at [email protected] or +39 035 4520075.

Catalog excerpts

ALL-IN ONE NDT TESTING Non-destructive testing instrument All-in One: a single acquisition unit that allows, through the purchase of several specific "Kit", to perform sonic and ultrasonic tests for the characterization in situ and in the laboratory of materials such as concrete, masonry and stone materials, "cross hole" and "PIT" (Pile Integrity Test) in piles and diaphragm foundations. All-in One system is a rugged and reliable equipment with various dedicated piezoelectric sensors and probes. All-in One is characterized by an A/D board multichannel and selectable sampling rates from 10KHz to 6.25MHz (up to 12.5MHz single channel). All acquired signals are displayed, computed and memorized directly on tablet pre-installed software. Connection between All-in One system and tablet via Wifi. APPLICATIONS • Verification of concrete elements on-site • Analysis of diaphragms and foundation piles • Seismic cross-hole test Solgeo - Via Pastrengo, 9 - 24068 Seriate (BG, Ita

Open the catalog to page 1

ALL-IN ONE NDT TESTING TECHNICAL CHARACTERISTICS Channel Converter type Input type Differential / Single ended / IEPE Input range range 1 to 40000 software selectable Sample rate up to 8K samples for each channel Travel time resolution Sample resolution antialias, digital filter selectable (DSP) hardware, software, threshold (selectable) Transmitter drive voltage Pulse duration Selectable Transmitter pulse repetition Piezoelectric-Type: See table TRANSDUCERS Power supply External recharging - recharging time 4h 1,8W Stand-by/ 2.8W Ultrasonic active › 35 hour standBy/ 20 hour working Working temperature...

Open the catalog to page 2

KIT CONTACT 55KHz ultrasonic transducers, with push-button control for automatic signal recording Dynamic monitoring of monuments interested in the excavation of Rome Metro C Accessories KIT All-in-One: - instrumented hammer with accelerometer for sonic investigations - 20kHz transducer - Punch for sonic investigation KIT PIT consisting of an instrumented hammer with accelerometer and accelerometric receiver KIT MCHA encoder with luminous signal for exceeding speed limit and push-button control panel KIT MCHA consinting of probes 80kHz (optionally 50kHz) with cable reel up to 100m

Open the catalog to page 3