With buffer Rotating, Non-rotating .Lateral vacuum Barb fitting (Compatible with NBR (Black), Silicon rubber (White), Urethane rubber (Brown), Fluoro rubber (Black with green mark), Conductive NBR (Black with one silver mark), Conductive silicon rubber (Black with two silver marks) Refer to the vacuum equipment model selection on pages 828 to 834 for the calculation of lift force and response time. © : Little or no influence O: Can be used depending on conditions X: Not suitable t The above table covers only general characteristics of subject rubber materials. Pad materials used by SMC pass the JIS standards; however the actual performance depends on operating conditions.

Vertical Vacuum Entry Without Buffer Mass/Male Thread (Female thread)_(g) * ( ): Figures for female thread connections

Vertical Vacuum Entry Without Buffer O0/76S Without buffer (Refer to "Table (1 )" for applications.) ' Vacuum entry/Mounting thread diameter Table (1) Pad Diameter/Pad Type Be sure to read before handling. Refer to front matters 38 and 39 for Safety Instructions and pages 844 to 846 for Vacuum Equipment Precautions. In cases where workpieces are heavy or dangerous, etc., take measures to address a possible loss of adsorption force (installation of drop prevention guides, etc.). In the case of transportation by vacuum adsorption using vacuum pads, adsorption force is lost when there is a drop...

Male thread Vacuum Entry Port Thin flat/Thin flat with ribs 010, 013, 016/Elli Flat/Thin flat/Thin flat with ribs Flat/Flat with ribs/Deep/Thin flat/ Thin flat with ribs/Elliptic_ Use connection for vacuum entry across flats Hexagon width across flats Hexagon width t ■-■ " Flat with ribs Flat/Thin Flat/Thin Flat with Ribs Flat/Flat with Ribs Hexagon width Hexagon width Flat with ribs Hexagon width " across flats Hexagon width across Hats , across flats Flat/Flat with Ribs Flat/Flat with Ribs

Vertical Vacuum Entry Without Buffer OOHOS Hexagon width Hexagon width Hexagon width Hexagon width

Female thread Vacuum Entry Port Flat/Flat with ribs/Deep Use connection for vacuum entry Flat/Thin flat/Thin flat with ribs Flat with ribs Hexagon width Flat/Flat with Ribs Flat Deep: ZPT1 OD/16D only Flat/Flat with Ribs Flat Deep: ZPT40D only Flat/Flat with Ribs

Vertical Vacuum Entry Without Buffer OOHOS Hexagon width Hexagon width Hexagon width Hexagon width

Vertical Vacuum Entry With Buffer Buffer Specifications * Refer to 02 to 08 for Thin flat, Thin flat with ribs and Elliptic. Thin section

Vertical Vacuum Entry with Buffer OÖ/76S With buffer 1 Mounting thread diameter/ Male thread fl(Referto "Table (3)" for applications.) Vacuum entry port (Refer to "Table (3)" for applications.) Buffer type Buffer stroke (Refer to "Table (2)" for applications.) Table (1) Pad Diameter/Pad Type Flat with ribs Thin flat Thin flat with ribs Thin flat/Thin flat with ribs Table (3) Vacuum Entry/Mounting Thread Diameter Tightening Torque

Thin Flat/Thin Flat with Ribs

Vertical Vacuum Entry with Buffer OOHOS Hexagon width across flats " Hexagon width Flat with ribs Hexagon width Flat/Flat with Ribs

Hexagon width across flats " Hexagon width Flat/Flat with Ribs

Vertical Vacuum Entry with Buffer OÖ/76S Hexagon width Hexagon width Flat with ribs

Vertical Vacuum Entry with Buffer OOHOS Hexagon width Hexagon width

Vertical Vacuum Entry with Buffer OOHOS Flat with ribs Flat/Flat with Ribs

Hexagon width across flats " Hexagon width Flat with ribs

Vertical Vacuum Entry with Buffer OÖ/76S Flat with ribs Flat/Flat with Ribs

Hexagon width

Vertical Vacuum Entry with Buffer OÖ/76S

Thin Flat/Thin Flat with Ribs

Vertical Vacuum Entry with Buffer OÖ/76S Hexagon width Hexagon width

Hexagon width Flat with ribs Flat/Flat with Ribs

Vertical Vacuum Entry with Buffer OÖ/76S Hexagon width Hexagon width Hexagon width Flat/Flat with Ribs Flat with ribs

Vertical Vacuum Entry with Buffer OOHOS

Lateral Vacuum Entry with One-touch Fitting Without Buffer Mass/Male Thread (Female thread) ( ): Figures for female thread connections.

Lateral Vacuum Entry with One-touch Fitting without Buffer Without buffer (Refer to 'Table (1)" for applications.) Table (1) Pad Diameter/Pad Type Mounting thread jQQj (Refer to 'Table (2)" for applications.) Vacuum entry port (Refer to "Table (2)" for applications.) Table (2) Vacuum Entry/Mounting Thread Diameter

Size/Flat a2, o4,06,08/Thin flat/Thin flat with ribs 0IO, o13,0I6/ Flat/Thin flat/Thin flat with ribs Thin Flat/Thin Flat with Ribs Flat with ribs Flat/Flat with Ribs

Lateral Vacuum Entry with One-touch Fitting without Buffer Flat/Flat with Ribs Flat/Flat with Ribs

Hexagon width across flats J^' ] Hexagon width across flats 10, Hexagon width acrossflats 7 ' ( fi I Applicable tubing O.D.eP Hexagon width across flats

Lateral Vacuum Entry with One-touch Fitting without Buffer Size/Flat o2, o4,06,08/Thin flat/Thin flat with ribs 0IO, 0I3,0I6/ Flat/Thin flat/Thin flat with ribs Hexagon width Hexagon width Hexagon width across flats 8 Flat with ribs Flat/Flat with Ribs

Flat Flat Flat/Flat with Ribs Applicable Tubine Flat/Flat with Ribs Applicable Tubine

Lateral Vacuum Entry with One-touch Fitting Without Buffer Hexagon width across flats 7 Hexagon width

Lateral Vacuum Entry with One-touch Fitting With Buffer Buffer Specifications * Refer to 02 to 08 for Thin flat, Thin flat with ribs and Elliptic.

Lateral Vacuum Entry with One-touch Fitting with Buffer With buffer (Refer to "Table (1)" for applications.) ■ Mounting thread/Male thread J^jQj (Refer to "Table (3)" for applications.) > Vacuum entry port jQQj (Refer to "Table (3)" for applications.) Buffer stroke (Refer to "Table (2)" for applications.) Buffer type Table (1) Pad Diameter/Pad Type ^"^^^ Diameter Thin flat/ Thin flat with ribs Table (3) Vacuum Entry/Mounting Thread Diameter Tightening Torque

Lateral Vacuum Entry with One-touch Fitting with Buffer Flat with ribs Flat/Flat with Ribs One-touch Fitting