Possible to easily supply dry air using the hollow fiber membrane! Non-fluorocarbon Compatible with low dew point (–60°C) No vibration or heat discharge Purge air flow rate [L/min [ANR]] Energy saving R Reduced in purge air flow by up to Existing model Purge air flow rate (rated conditions) Reduced purge Purge air flow rate Purge ratio [L/min [ANR]] [%] Running cost [€/year] [Calculation conditions] Air unit price: 0.02 €/m3 Operating hours: 12 hours/day Annual operating days: 250 days/year Variations Unit Type Single Unit Type Reduced purge IDG२A Series IDG२A Purge air flow reduction type A white body is introduced. Mist separator Micro mist separator Micro mist separator Tube configuration low flow rate type When dry clean air and pressure control are required. Mist separator When dry clean air is required. Single Unit Body size Standard dew point

T Space Total length is shortened. saving Max. 59 mm M T High Time to reach the rated dew point performance Shortened by 40 minutes S Reduced purge IDG२A Series Under SMC test condition Time to reach the rated dew point (minutes) Existing model ∗ Standard dew point: –40°C/L, –60°C/H Reduced purge Existing model Existing model Dew point indicator visually confirms air drying. (Except IDG1) (Optional on IDG3, IDG5, IDG3H, IDG5H) Colour of the dew point indicator ¼ Normal operating: Blue ¼ Initial state: White/Pink Fitting for exhausting purge air for dew point indicator Model with fitting for purge...

Series IDGU A/IDG Dehumidification Principle The membrane air dryer uses hollow fibers composed of a macro molecular membrane through which moisture passes easily, but is difficult for air (oxygen and nitrogen) to pass through. When humid, compressed air is supplied to the inside of the hollow fibers, only moisture permeates the membrane and moves to the outside between the moisture inside and outside of the fibers. The compressed of the dryer. Part of the dry air from the outlet side is passed through a very small orifice to reduce the pressure and purge the outside of the hollow fibers. The...

Series Variations Meets a wide variety of flow rates (10 to 1000 L/min [ANR]) and dew points (Atmospheric pressure dew point: –15°C to –60°C). Single Unit Type Standard dew point: –20°C Standard dew point: –15°C Standard dew point: –40°C Standard dew point: –60°C Series Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] Note) Standard dew point: Outlet air atmospheric pressure dew point under standard performance conditions Outlet air flow rate: Values under standard performance conditions

Series IDG २A/IDG Unit Type A mist separator, micro mist separator, or micro mist separator with pre-filter combined with a single unit Standard dew point: – 20°C Standard dew point: –15°C Standard dew point: – 40°C Standard dew point: – 60°C Series Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] Outlet air flow rate [L/min [ANR]] ∗ Rated conditions are 0.7 MPa of inlet air pressure and 25°C of inlet air temperature. A regulator combined with the type M Standard dew point: – 20°C Standard dew point: –15°C Standard dew point: – 40°C Standard...

Membrane Air Dryer/Single Unit Type Reduced purge IDG२A Series Standard dew point −20°C, −15°C, −40°C, −60°C How to Order Reduced purge IDG२A Series Standard dew point temperature and air flow rate Flow direction (Right → Left) With fitting for purge air discharge Note) In the case of two or more options, indicate them alphabetically. Thread type Symbol None (Standard) None (Standard) Standard Flow rate by size Outlet air flow rate [L/min [ANR]] Symbol dew point 30 50 60 75 100 [°C] −20 300 500 — Select from Series IDG −15 300 500 H With bracket Note) When symbol B is indicated, a bracket assembly...

Membrane Air Dryer/Single Unit Type Single Unit Type None (Standard) Standard dew point temperature and air flow rate Model Selection Accessory Symbol With bracket (Except IDG1) Note) When symbol B is indicated, a bracket assembly with a part number shown in the table left below is included as an accessory. Select from Series IDG२A Unit Type Port size Port size Thread type Bracket Assembly (Accessory) Part No. Part no. b Flow direction (Right → Left) — With dew point indicator — None (Standard) With fitting for purge air discharge Specific Product Precautions Standard equipment Note) In the case...

Reduced purge IDG२A Series Standard Specifications/Single Unit Type (Standard dew point −20°C, −15°C) Standard dew point…−20°C IDG1 Standard performance conditions Range of operating conditions Model Fluid Inlet air pressure [MPa] Inlet air temperature [°C] Note 1) Ambient temperature [°C] Note 1) Standard Outlet air atmospheric perfor- pressure dew point [°C] mance Inlet air flow rate [L/min [ANR]] Note 2) Outlet air flow rate [L/min [ANR]] Purge air flow rate [L/min [ANR]] Note 3) Inlet air pressure [MPa] Inlet air temperature [°C] Inlet air saturation temperature [°C] Ambient temperature [°C]...

Membrane Air Dryer/Single Unit Type Reduced purge IDG२A Series Standard Specifications/Single Unit Type (Standard dew point −40°C, −60°C) Standard performance conditions Range of operating conditions Model IDG30LA IDG50LA IDG60LA IDG75LA IDG100LA Compressed air Fluid 0.3 to 1.0 Inlet air pressure [MPa] −5 to 50 Inlet air temperature [°C] Note 1) −5 to 50 Ambient temperature [°C] Note 1) Standard Outlet air atmospheric perfor- pressure dew point [°C] −40 mance Note 2) 400 93 135 224 308 Inlet air flow rate [L/min [ANR]] 300 75 110 170 240 Outlet air flow rate [L/min [ANR]] 100 18 25 54 68 Purge...