Hygienic Design Cylinder A water resistant cylinder configured for easy cleaning resistant configured ISO standard type Series HYC Basic type Series HYQ With guide Series HYG

A water resistant cylinder c Scraper Flat, grooveless configuration Eliminates the auto switch groove and the holes for cushion needle holes, etc. Plug bolt (Optional) Conventional Cushion needle HYC Plug bolt (Optional) External cover (Optional) Five times increase in service life compared to conventional model (SMC ratio) Water-proof examination result (Reference data) 1 Hygienic Design Cylinder (HYB, HYQ, HYC, HYG) Water resistance improvement cylinder Comparison with conventional model: Approx. Standard cylinder Washing in water/Temperature: 30°C, Flow rate: 160 cc/min Grease for food (NSF-H1...

onfigured for easy cleaning Plug bolt (Optional) New scraper Grease retention in guide rod and cylinder rod Breathing port on guide (PAT.) Water dispersion environment General environment Piping at the breathing port on guide allows breathing outside the water dispersion environment. Special coating (PAT.) Guide accommodates a special coating. Plug 2. Lower side mounting Application: Plug bolts are used to close the mounting hole not used. Mounting hole of the bottom surface is closed. Bore size 2. Lower side mounting Mounting hole of the top and bottom surface is closed. Mounting hole of the...

Hygienic Design Cylinder Round Type Without auto switch With auto switch H7BAL Number of auto switches With auto switch (Built-in magnet) Auto switch Port thread type Nil TN TF Without auto switch (Built-in magnet) Refer to table below for selection of applicable auto switch. Auto switch is shipped not assembled with the cylinder. Standard grease (for non-food) Grease for food Note) Select grease for food for use in a water dispersion environment or when washing a product with water. (Water resistance is insufficient with standard grease.) Note) External seal material: Rod scraper, tube gasket,...

Hygienic Design Cylinder Round Type Bore size (mm) Action Double acting, Single rod Minimum operating pressure Maximum operating pressure Proof pressure 1.5 MPa Without auto switch 0 to 70°C Ambient and operating fluid temperature With auto switch 0 to 60°C Not required 50 to 500 mm/s (With pressure at 1.0 MPa) Note) Piston speed Cushion Stroke length tolerance Piston rod material Stainless steel 304 / Hard chrome plated Note) Use a cylinder below the allowable kinetic energy. Refer to page 3 for the allowable kinetic energy. Standard Stroke Bore size (mm) ∗ Intermediate strokes of 1 mm each...

Series HYB Allowable Kinetic Energy Maximum drive speed (V mm/s) Stroke (mm) • A case where the center of gravity of the load rests 50 mm from the rod end.

Hygienic Design Cylinder Round Type

Hygienic Design Cylinder Basic Type Without auto switch With auto switch R 50 F M R 50 F M F6B Number of auto switches With auto switch (Built-in magnet and switch rail) Auto switch Port thread type Nil TN TF Refer to table below for selection of applicable auto switch. Auto switch is shipped not assembled with the cylinder. Without auto switch (Built-in magnet and switch rail) Female thread Male thread Note) External seal material: Rod scraper, tube gasket, and rod seal are made from FKM. Cylinder stroke < Mounting bracket > Foot, flange, single clevis, double clevis, and clevis pin < Option...

Hygienic Design Cylinder Basic Type Specifications Bore size (mm) Action Fluid Minimum operating pressure Maximum operating pressure Proof pressure Ambient and operating fluid temperature Double acting, Single rod Air 0.2 MPa 0.15 MPa 1.0 MPa 1.5 MPa Without auto switch 0 to 70°C With auto switch 0 to 60°C Not required 50 to 500 mm/s (With pressure at 1.0 MPa) Note) Rubber bumper +1.4 0 mm Stainless steel 304 / Hard chrome plated Lubrication Piston speed Cushion Stroke length tolerance Piston rod material Note) Use a cylinder below the allowable kinetic energy. Refer to page 7 for the allowable...

Series HYQ Allowable Load at Rod End Allowable Kinetic Energy (Supply pressure: at P = 0.5 MPa) Maximum drive speed (V mm/s) Stroke (mm) • A case where the center of gravity of the load rests 50 mm from the rod end.

Hygienic Design Cylinder Basic Type Construction: ø20, ø25 Basic type Built-in magnet Aluminum alloy Anodic oxide film Head cover Aluminum alloy Anodic oxide film Cylinder tube Aluminum alloy Anodic oxide film Aluminum alloy Stainless steel Hard chromium plated Bushing retainer Aluminum alloy Hexagon socket head cap screw Stainless steel Piston seal Tube gasket Stainless steel (Only built-in magnet) Magnet holder Aluminum alloy (Only built-in magnet) Chromated Switch rail base Stainless steel (Only built-in magnet) Hexagon bolt Stainless steel (Only built-in magnet) Switch rail Stainless steel...

Series HYQ Construction: ø32 to ø63 Basic type Built-in magnet Aluminum alloy Anodic oxide film Magnet holder Aluminum alloy (Only built-in magnet) Chromated Head cover Aluminum alloy Anodic oxide film Switch rail base Stainless steel (Only built-in magnet) Cylinder tube Aluminum alloy Anodic oxide film Hexagon bolt Stainless steel (Only built-in magnet) Aluminum alloy Switch rail Stainless steel (Only built-in magnet) Stainless steel Hard chromium plated Bushing retainer Aluminum alloy Hexagon socket head cap screw Stainless steel Piston seal (Only ø63 is common to the bumper A.) Tube gasket...

Hygienic Design Cylinder Basic Type Dimensions Without auto switch: HYQB20, 25 Q H thread effective depth C Rod end male thread Width across flats KA Width across flats B1 Rod End Male Thread Bore size Bore size Stroke range 50 or less 50 or less Note 1) Refer to page 32 for details about the rod end nut, mounting bracket and accessory bracket. Note 2) When the unit is installed, ensure that dirt does not collect in the rod end (threaded portion).

Series HYQ Dimensions With auto switch: HYDQB20, 25 Q H thread effective depth C [Width across flats 3] Rod end male thread Width across flats KA Width across flats B1 Rod End Male Thread Bore size Bore size Stroke range 50 or less 50 or less Note 1) The [ ] value denotes dimensions with the auto switch D-F6 mounted, which is dedicated to the Hygienic Design Cylinder. Note 2) Refer to page 32 for details about the rod end nut, mounting bracket and accessory bracket. Note 3) When the unit is installed, ensure that dirt does not collect in the rod end (threaded portion).